DIY pyöreän sohvapöydän muuntajan piirustukset. Muunnettava sohvapöytä
Olen pitkään haaveillut muuttuvasta pöydästä meidän Hruštšovin aikaisissa rakennuksissa, se ei voi olla toisin. Kaikki huoneet ovat aina täynnä huonekaluja ja kaikenlaista. Halusin jotenkin vähentää huonekalujen määrää, mutta en menetä toimivuutta. Löysin vastauksen tähän kysymykseen kauan sitten muunnettavissa olevista huonekaluista, mutta se oli kallis ostaa, enkä uskaltanut tehdä sitä itse.
Oli ajanjakso, jolloin keräsin kaikki materiaalit ja suunnittelin jo pöydän tekemistä, mutta ensimmäisen ongelman edessä - muunnosmekanismin tekeminen tai ostaminen - hylkäsin idean heti. Ja yhtäkkiä palasin ajatukseen muuntajan pöydän kokoamisesta omin käsin - olohuone oli remontissa, oletettiin, että remontin jälkeen 350 litran akvaario muuttaa huoneeseen, ja oli selvää, että siellä ei voi enää olla kysymys siitä, että tässä huoneessa olisi täysi pöytä. Päässäni nousi vanha unelma muunnettavasta pöydästä ja kaikki alkoi pyörimään.
Mestariluokan kuvaus
Taulukon muunnosmekanismin valinta.
Valitsin sopivan mekanismin pöydän muuntamiseen. Ensin valitsin pöydän asettelun, pidin todella Acrobat-mekanismista, mutta sitä ei toimiteta Venäjälle. No, ainoa markkinoilla saatavilla oleva vaihtoehto oli seuraavan periaatteen mekanismi:
Tätä mekanismia valmistetaan sekä Venäjällä, ja analogeja on Euroopasta ja Kiinasta. Tuettu venäläistä valmistajaa! Mekanismissa on jouset tai kaasunostin, joita tarvitaan pöydän avaamiseen/taittamiseen - pehmeämpään ajoon. Epäilemättä valitsin jousella varustetun vaihtoehdon, koska... Mitä yksinkertaisempi muotoilu, sitä luotettavampi se on. Lisäksi jousi on piilotettu mekanismin runkoon, eikä se ole näkyvissä pöytää avattaessa, toisin kuin kaasunostin, joka on liian havaittavissa.
Muuntajapöydän suunnittelu.
Tein tulevaisuuden taulukon asettelun PRO100-ohjelmassa. Käytin tätä ohjelmaa ensimmäistä kertaa elämässäni, keksin sen yhdessä illassa. Suunnitelman tein noin kahdessa illassa. Otin netistä kuvan samanlaisesta taulukosta vakiona ja laskin mitat itse. Siitä ei tullut mitään monimutkaista. Monet suositukset lähetettiin ennen mekanismin ostamista, ohjasin niitä kokoja laskettaessa.
Laminoidun lastulevyn leikkaaminen ja reunustaminen.
Tilasin lastulevyn leikkaamisen. Itse asiassa PRO100-ohjelmalle on olemassa sovellus, joka tekee leikkauskartan, mutta koska... Olin liian laiska etsimään ja selvittämään sitä - joten tein leikkauskartan manuaalisesti ja melko nopeasti.
Kartallani on myös kolmannen osapuolen elementtejä, koska... Tilasin toisen kaapin pöydän kanssa. Nämä lisäelementit on merkitty karttaan X:llä. Laminoidun lastulevyn väri oli wenge, paksuus muunnosmekanismin valmistajan suosittelemana 22mm. Pöytälevyn tulee olla vähintään näin paksu. Mekanismi on suunniteltu tällaiseen kuormaan, itse pöydän runko voidaan valmistaa 16 laminoidusta lastulevystä. Mutta kaikki eivät tilaa 2 eripaksuista arkkia suurella määrällä romuja) Tilasin reunuksen heti leikkauksella, pöytälevy oli 2mm PVC-reuna, loput tavallinen melamiinireuna.
Osien ensimmäinen asennus.
Toin sahattua ja kehystettyä lastulevyä. Ostin kokoamiseen tarvittavat tarvikkeet. Yritin taittaa elementit uloshengittämistä varten ja varmistaa, että en ollut tehnyt virhettä kokojen kanssa. Kaikki toimi, olin oikeassa kokojen kanssa.
Pöydän rungon kokoaminen.
Kokoamme pöydän rungon vahvistuksiin erikoisporalla. Merkitsemme tummiin lastulevyihin tarroilla. Tämä idea tuli yllättäen, kun yritin tehdä merkintöjä lyijykynällä tummalle laminoidulle lastulevylle: mitään ei näkynyt ja kynä heijastui ja häikäisi. Tarra ratkaisi tilanteen - merkinnät ovat tarkkoja eikä lastulevyyn ole jäänyt liiman jälkiä. Lisäksi ratkaisu on melko halpa.
No, varsinainen pöytäkehyksen kokoaminen vahvistuksia varten:
Kiinnitämme mekanismin päästä päähän -menetelmällä, koska Mekanismin paino on vaikuttava - 8 kg. joka. Ei tarvitse pelätä, koska... Meillä on kaikki laskettu ja yläjalat piilottavat kaikki tekniset reiät ja kiinnitykset. Teemme merkinnät mekanismin kiinnittämiseksi samalla tavalla
Poraamme ruuveille reiät läpi ja valmistelemme sitten Fosner-poralla paikan, jossa pultin kannat voivat upottaa ne.
No, pultaamme mekanismin. Pulttien määrää ei kannata pelätä, ne ovat kaikki välttämättömiä, ne kiinnittävät pöydän seinät entistä lujemmin yhteen ja tekevät niistä itsekantavia.
Muuntajan pöydän jalkojen kokoaminen.
Pöydän jalkojen kokoaminen. Jalkojen tulee olla erittäin vahvoja kestämään pöydän painon (joka on noin 45 kg) ja sillä olevien astioiden painon. Siksi päätettiin kiinnittää jalat yhteen siteillä.
Ruuvaa jalat kiinni pöytään. Tätä varten sinun on merkittävä jalkojen kiinnikkeet erittäin tarkasti. Jotta asiat olisivat yksinkertaisia, porasin paikalleen. Asennamme sen näihin metalliholkkeihin
Heille poraamme reikiä jalkoihin merkin mukaan.
Tämä on asento, jossa kaikki jalat ruuvattiin. Jalat piilottavat kaikki tekniset reiät pöydän rungossa.
Pöytälevyn kokoaminen.
Pöytälevy on koottava erityisen tarkasti, koska pöytälevyn taittosaranan tulee olla vahva ja varmistaa pöytälevyn tasainen taittuminen/avautuminen. Kun ostin sen, epäilin saranoita ja hyvästä syystä. Periaatteessa ne toimivat, mutta saranaa on vaikea pitää hylsyissään, eivätkä ruuvit, joiden on tarkoitus tehdä tätä, tee työtä. Siksi suosittelen katsomaan muita pöytälevyn saranoita. Reikien merkitseminen työtasoihin:
Työtasot koottu
Näin muunnettavan pöydän vain valokuvissa tai videossa, minulla ei ollut mahdollisuutta pohtia sitä livenä. Mutta todella halusin tällaisen taitettavan pöydän seisomaan olohuoneeseemme, koska siinä on monia etuja. Taitettuna se on sohvapöytä ja avattuna täysi ruokapöytä, joka avautuu muutamassa sekunnissa.
Huonekalujen verkkokaupat tarjoavat kunnollisen valikoiman tällaisia pöytiä, mutta hinnat eivät jotenkin ole erityisen rohkaisevia. Ja minulle itselleni huonekaluja valmistavana ihmisenä oli mielenkiintoista tehdä ne omin käsin.
Tämän taitettavan pöydän tärkein kohokohta on muunnosmekanismi. Nyt se löytyy myös myynnistä. Mutta miksi kuluttaa ylimääräistä rahaa. Siksi päätin tehdä pöydän kokonaan omin käsin ilman ostettuja muunnosmekanismeja.
Aloitin työni etsimällä tarvittavaa tietoa Internetistä. Mikä tärkeintä, halusin löytää yksityiskohtaisia piirustuksia muunnosmekanismista. Koska olen kootanut huonekaluja useiden vuosien ajan, sekä itselleni että tilauksesta, minulla ei ollut epäilystäkään siitä, että osaisin koota pöydän, mutta muunnosmekanismiin en ollut ennen törmännyt. Siksi tärkeimmät ponnistelut kohdistuivat tiedon löytämiseen hänestä.
Omistin tälle työlle useita iltoja, ja lopulta alkoi muodostua yleiskuva mekanismista, mitä sen pitäisi olla. Halusin saada muunnosmekanismin saataville kokoonpanossa. Jotta sitä asennettaessa sinun ei tarvitse tehdä erityisiä töitä, kuten hitsata osia, tai käyttää sorvaajalta tilauksesta valmistettuja osia. Kaikkien komponenttien tulee olla vapaasti saatavilla.
Päätettiin, että mekanismilla olisi oma runko (laatikko), jonka tekisin huonekalulastulevystä. Liikkuvat osat teen 20x20mm profiiliputkesta. Pyörimisakseleina käytetään pultteja, joiden halkaisija on 8 mm. Ja huonekalujen julkisivujen kaasuhissejä käytetään apunostoelementteinä.
Nyt oli tarpeen suunnitella kolmiulotteinen malli muunnosmekanismista (MT). PRO100-ohjelma ei ollut aivan sopiva näihin tarkoituksiin, joten jouduin nopeasti opettelemaan toisen 3D-mallinnusohjelman. Helpoin ohjelma minulle oli Googlen Sketch Up. Siinä tein MT-projektin työpöydälleni.
Ja sitten malli koko pöydästä.
Oli aika siirtyä virtuaalisesta mallintamisesta todelliseen mallinnukseen. Toimivuuden testaamiseksi tein mallin rakennuslastulevystä. Siitä tein laatikon ja melkein kaikki mekanismin osat. Tämä mahdollisti sen, että suunniteltu MT toimii. Valitettavasti lastulevytelineet osoittautuivat hauraiksi ja mallin pudotessa pöydältä kaksi neljästä hajosi.
Olen jo työskennellyt perusteellisemmin tämän mallin kanssa. Selvensin kaikki mitat ja muutin hieman alkuperäistä suunnittelua. Jouduin kärsimään todella pitkään miettiessäni, miten kaasuiskunvaimentimet sijoitetaan niin, että ne auttaisivat pöytää avattaessa. Luultavasti purin ja kokosin muunnosmekanismin kahdeksan kertaa vaihtaen iskunvaimentimen kiinnityksen asentoa halutun tuloksen saavuttamiseksi.
Nyt minulla oli kaikkien osien tarkat mitat, tiesin mihin ja mitä reikiä piti porata. Tein kolmiulotteisen mallin MT:stä PRO100-ohjelmalla.
Ostin kaikki tarvittavat materiaalit ja aloitin kokoamisen.
Kahden muunnosmekanismin tekemiseen käytin seuraavia materiaaleja ja lisävarusteita:
putki 20x20 - 16 pm;
putki 50x25 - 1,2 pm;
nauha 20x4 - 1 mp;
pultti m8x120 - 6 kpl;
pultti m8x60 - 2 kpl;
mutteri M8 - 26 kpl;
aluslevy 30x8 - 24 kpl;
leikkaustasoite - 12 kpl;
kulma 45x25 - 0,06 pm;
pultti m8x50 - 2 kpl;
pultti m4x20 - 8 kpl;
kaasu-iskunvaimennin 120-140N - 4 kpl;
Lastulevy - 0,3 neliömetriä m
Jokaisen mekanismin paino oli hieman yli viisi kiloa.
Arvioitu materiaalikustannus on 33 dollaria.
Tältä kootut mekanismit näyttävät.
Nyt voidaan alkaa tehdä pöytää.
Minulla ei ollut vaikeuksia pöydän suunnittelussa, koska se on tuttu tehtävä. PRO100-ohjelmassa tein ensin projektin useista pöytävaihtoehdoista.
Pidin ensimmäisestä vaihtoehdosta enemmän, joten päätin tehdä sen. Lisäksi tein tälle pöydän versiolle suunnittelun Basis-Furniture Maker -ohjelmassa, jotta ei kuluisi aikaa kiinnikkeiden mittojen laskemiseen käsin.
Ostin tarvittavat tarvikkeet:
epäkeskoliitin - 16 kpl;
vahvistus - 32 kpl.;
itsekierteittävä ruuvi 4x30 - 32 kpl;
muovinen kaksoiskulma - 4 kpl;
itsekierteittävä ruuvi 4x16 - 8 kpl;
jalka D8 m6x13 - 12 kpl;
pultti m6x30 - 2 kpl;
pultti m6x20 - 8 kpl;
pultti m6x15 - 4 kpl;
saranat - 3 kpl.
Huonekalulastulevy kahdessa värissä, tumma ja vaalea:
Kevyt lastulevy 16mm - 1,92 neliömetriä. m;
Tumma lastulevy 16 mm - 2,69 neliömetriä.
Yhteensä lastulevyn leikkaamiseen ja reunojen liimaukseen tarvittavat materiaalit ja palvelut maksoivat 75 dollaria.
Kokoonpanoprosessi ei kestänyt minulta kovin kauan, vaikka loppuvaiheessa ilmeni yksi vivahde, joka viivästytti työtä. Mutta lopulta kaikki meni minulle ja yleisesti ottaen olin tyytyväinen työhön. Tekemäni pöytä näyttää tältä.
Pöytä osoittautui melko kestäväksi, se tukee varmuudella painoani, joka on hieman yli sata kiloa.
Muutosmekanismi toimii hyvin. Avasin ja taitin pöydän monta kertaa, osissa ei ollut välystä. Mutta tarvittaessa voit aina tehdä tarvittavat säädöt vapaan pääsyn muunnosmekanismiin. Yläosan lähellä olevien metalliliuskojen maali on hieman naarmuuntunut. Todennäköisesti taitettaessa telineet hankaavat tukitankojen reunoja vasten. Mutta tämä ei ole kriittinen, koska se ei ole havaittavissa ollenkaan.
Pöydän avaaminen ei ole vaikeaa, vaikka kaasuiskunvaimentimet alkavat tarjota huomattavaa apua vasta puolivälissä. Pöydän paino on noin kolmekymmentä kiloa, se on melko vakaa.
Pöydän ääressä istuminen on 180 cm:n pituiseni varsin mukavaa, istuessani keskellä pöytää, polveni koskettivat pöytää. Muuten, kahden mekanismin välissä olevaa pöydän alla olevaa syvennystä voidaan käyttää pöytäliinojen, lautasliinojen ja muiden kattaukseen tarkoitettujen tavaroiden säilyttämiseen.
Mutta positiivisin asia on muiden reaktio. Katsokaa vaikka ystävieni ilmettä, kun heidän silmiensä edessä sohvapöytä muuttuu, en sanoisi, elegantiksi, mutta silti täysipainoiseksi ruokapöydäksi. Puhumattakaan pyynnöistä tehdä niistä samat.
Nyt asian taloudellinen puoli. Tämän kopion valmistus maksoi minulle hieman yli sata dollaria. Tällaisen pöydän keskihinta verkkokaupoissa on vähintään kaksinkertainen. Samalla pöytä näyttää juuri sellaiselta kuin halusin. Tällaisen muunnosmekanismin perusteella on mahdollista kehittää minkä tahansa mallin tai mallin pöytä, esimerkiksi pöytäpöytä.
Jos olet kiinnostunut piirustuksista ja yksityiskohtaisesta kuvauksesta muuntajapöydän valmistuksesta, lue ehdotukseni napsauttamalla linkkiä.
Luotu 07 toukokuuta 2014 | |||||||||
Alkuperäinen terve järki kehottaa sinua kokoamaan muunnospöydän omin käsin - kustannussäästöt vaihtelevat tässä tapauksessa 50-75% mallista ja materiaaleista riippuen. Jatkettavan pöydän valmistaminen ilman merkittävää ajanhukkaa ei ehkä ole mahdollista, jos tämä on ensimmäinen kokemuksesi huonekalujen valmistuksessa. Aikaa kuitenkin kompensoivat hankitut taidot, joiden ansiosta jatkoprojektit voidaan toteuttaa paljon nopeammin. Loppujen lopuksi yksikään kodin isäntä ei ota instrumenttia käteensä vain kerran: olohuoneessa, makuuhuoneessa, käytävässä on aina paikka käyttää voimaa ja luovaa mielikuvitusta.
Taitettava kirjapöytä
Monissa perheissä suurta ruokapöytää ei tarvita ympäri vuoden. Sen läsnäolo voi kuitenkin auttaa vieraiden saapuessa. Liukumekanismi sopii näihin tarkoituksiin ihanteellisesti sillä varustettu vaatimaton puinen pöytä seisoo huomaamattomasti nurkassa suorittaen aputoimintoja. Mutta kun hänen aikansa tulee, hän seisoo asunnon keskellä.
On ehdotettu, että tehdään runkohuonekalumekanismi, jossa on kannen alapuoliset. Materiaalit, joita tarvitset:
- höylätyt tangot 20x50 mm;
- vaneri tai ohuet 10 mm lankut (laatikoille);
- huonekalulevy: lastulevy, laminoitu lastulevy tai MDF (kannessa).
Kuva 1. Piirustukset taitettavasta pöytäkirjasta: 1 – käyttörunko; 2 – pyörivä runko; 3- taitettava taso; 4 – laatikko; 5 – päärungon sivuosan asennus (vaihtoehto B); 6 – keskikapea lastulevypöytätaso B
Kuva 2. Pöydän asennuskaavio: 2 – pyörivän rungon elementit; 3- taitettava taso; 4 – laatikko; 5 – ajorunko
Pöytäkirjan kokoamismekanismi:
- Pöydän jalat sahataan haluttuun pituuteen.
- Niihin tehdään merkinnät.
- Merkintöjen mukaan pitkittäislaatikoita varten on koverrettu urat (pöydän jalkoja yhdistävät poikittaiset säleet).
Huomio! Alempien säleiden urat voidaan tehdä mielivaltaiselle korkeudelle, ja ylempiä säleitä koverrettaessa on otettava huomioon laatikon korkeus.
- Pitkittäiset laatikot on sahattu pituudeltaan.
- Yksittäiset piikit viilataan alas niiden päistä.
- Liimaa sivukehykset (2 kpl), kun olet tarkistanut kokoonpanon tarkkuuden neliöllä.
- Kun sivukehykset kuivuvat, tee 2 tukea pöydän sivupeitteille. Ne ovat myös runkorakenteisia (kuvassa 1 ja 2 - nro 5).
Pöytäkirjan asennus
Tukijalkojen pituus vastaa pöydän jalkojen korkeutta. Toisen pystypylvään koko vastaa pitkittäiskehysten ulkoreunojen välistä etäisyyttä. Ja jotta taitettu tuki ei katso pöydän ulkopuolelle, tuen leveyden tulee olla yhtä suuri kuin puolet pöydän sivujen pituudesta.
Pöytäkirjan kokoamismekanismi (jatkuu):
- Tukemiseen tarkoitettuihin tankoihin on aika tehdä yksiläpivienti- ja sokeat tappiliitokset.
- Tangot liitetään liimalla.
- Sahaa kuivuneisiin sivuseiniin ja valitse syvennykset lyhyiden poikittaisten laatikoiden kiinnitystä varten (nro 2 kuvassa).
- Näiden lyhyiden laatikoiden sivut on yhdistetty liimalla ja ruuveilla.
- Ohjaimet on kiinnitetty ylempien pitkittäisten laatikoiden sisäpuolelle laatikoiden siirtämistä varten (nro 4 kuvassa).
- Laatikoiden (kaappien) sivuseinät on valmistettu vanerista tai ohuista 10 mm levyistä.
- Kaapin etuseinä tulee tehdä paksummasta levystä.
- Neljännekset leikataan näiden lautojen reunoja pitkin laatikon sivujen kiinnittämiseksi.
- Kaikki kaapin elementit pidetään yhdessä liimalla ja ruuveilla.
- Kaapien (laatikoiden) pohja on leikattu ohuesta vanerista tai kuitulevystä.
- Huomio! Suunnittelun erityispiirre on, että laatikon etuseinä ulottuu jalkojen sisään. Tämä tarkoittaa, että seinän etutaso ja jalkojen reunat ovat samassa tasossa. Ja tämän saavuttamiseksi johteisiin ja ylempiin pitkittäisiin vetolaatikoihin on kiinnitetty puristimet, jotka eivät anna laatikon liikkua tarpeellista pidemmälle (kaaviossa nro 3).
- Pöytälevyt leikataan lastulevystä, laminoidusta lastulevystä tai MDF:stä. Aloita työ merkitsemällä ja leikkaamalla keskikansi.
- Huomio! Pöytärakenteen yläpuolella olevan keskikannen reunat ulkonevat 20-25 mm. Näin tukituki voidaan piilottaa kannen alapuolen alle.
- Keskimmäinen kansi on kiinnitetty neljällä metallikulmalla (nro 3 kuvassa), jotka on ruuvattu ruuveilla ylempien poikittaiskehysten sisäpuolelta.
- Sivusuojukset kiinnitetään keskimmäiseen pianosilmukalla. Se on ruuvattu alapuolelle ruuveilla.
- Huomio! Jos käännät huonekalurakenteen ympäri, yhdistät kaikki kannet ja vasta sitten alat kiristää saranoita, on mukavampaa työskennellä.
Oli tavallista - muuttui taitettavaksi
Kokoaaksesi muuntavan pöydän omin käsin, sinun ei tarvitse aloittaa kaikkea alusta. Voit muuntaa olemassa olevan puisen yksi- tai kaksijalustaisen pöydän liukuvaksi huonekalumekanismiksi. Suunnitteluratkaisu molemmissa tapauksissa ei ole erityisen erilainen - pöydät on varustettu sisäänvedettävällä elementillä.
Kuva 3. Mekanismia, jolla kaksijalustainen pöytä muunnetaan liukuvaksi, on esitetty ylälaatikon (1) etupaneelissa; kestävä lastulevylevy (2); silmukat (3); vaakasuora lastulevy (4); ruuvit (5)
Kahden jalustan pöydän modernisoimiseksi, kuten piirustukset osoittavat, on tarpeen päästä eroon oikean kaapin ylälaatikosta. Jos olohuoneen pohjaratkaisun vuoksi sinun on helpompi erota vasemman kaapin ulosvedettävästä kaapista, suorita projekti peilikuvana. Tämä ongelma ei ole olennainen; valittu pöytälaatikko on purettava kokonaan. Vain sen etupuolen, jossa on kahva, tulee jäädä.
Tähän levyyn on kiinnitetty toinen levy päädyssä olevilla ruuveilla (5), joiden mitat ovat samat kuin aiemmin siellä olleen laatikon mitat. Saranat (3) ruuvataan alhaalta, joihin painelevy (2) on kiinnitetty.
Laudan nro 2 tulee taitettuna olla tiiviissä kosketuksessa levyn nro 4 kanssa, jotta laatikosta vapautuvaan tilaan pääseminen on ongelmatonta. Jatkettaessa lauta nro 4 toimii lisäpöytänä ja lauta nro 2 sen tukena. Vääristymien välttämiseksi tämä taso on kallistettava kokonaan 90°.
Erot yksijalkaisen pöydän jälkiasennuksessa
Pöytä, jossa on yksi kaappi, lisää modernisoinnin jälkeen pinta-alaansa paljon enemmän kuin kaksijalusta. Lisäksi sen purettu geometria eroaa kaksijalustaisen rakenteen asettelusta.
Kuva 4. Mekanismia yksijalustaisen pöydän muuntamiseksi laajennettavaksi esitetään vaakasuoralla leikkauksella (1); pöytälaatikot (2); sisäänvedettävä levy (3); työntölevy (4); työntölevyn pyörät (5); neliöt (6); pöydän sivuseinä (7); lisäsäleet (asento 8)
Kuten ensimmäisessä tapauksessa, sinun on poistettava laatikot. Mutta tällä kertaa se ei ole kaapissa sijaitsevia kaappeja, vaan itse pöydän yläosassa olevia laatikoita. Molemmat laatikot on poistettava ja laatikon vasemmalle puolelle on tehtävä vaakasuora leikkaus (1). Valmiin aukon leveyden tulee olla yhtä suuri kuin valitun liukulaudan (3) paksuus, josta tulee lähitulevaisuudessa pitkänomaisen pöydän taso.
Mekanismi sisäänvedettävän levyn tasaiselle liukumiselle pöydän muodostetussa sisäisessä syvennyksessä on varustettu lisäsäleillä (8), jotka on asennettu sen liikesuuntaa pitkin. Jotta lauta ei putoa huonekalun sisään menevästä päästä, sinun tulee tehdä 2 tulppaa. Toisen pään sivulta liukulautaan on kiinnitetty 90° kulmassa neliöillä (6) pyörillä (5) oleva työntölevy (4). Lauta nro 4 on kiinnitetty tiukasti lautaan nro 3, ja koottuna se sopii tiukasti pöydän (7) sivuseinään. Paikkaan, jossa laatikot (2) aiemmin sijaitsivat, asennetaan koristelevy, jonka jälkeen liukuvaa huonekalumekanismia voidaan pitää käyttövalmiina.
On selvää, että pöytäsi mitat voivat poiketa piirustuksistamme. Kuitenkin kaikkien elementtien mitat ja pöydän uudelleenasennusmekanismi, joka on esitetty kuvassa. 3 ja 4 voidaan ottaa lähtökohtana muunnoksia suoritettaessa.
Kaksitasoinen pöytä
Ehdotettua puupöytää voidaan käyttää sohvapöytänä ympäri vuoden. Tarvittaessa se kuitenkin muuttuu helposti ja tyylikkäästi olohuoneen koristeeksi - suureksi ruokapöydäksi. Tämän tuotteen piirustukset eri lähteistä voivat poiketa hieman, tarjoamme optimaaliset koot. Arvioi itse, taitettuna tämä on upea sohvapöytä, jonka korkeus on 752 mm. Mutta nostamalla rakenteen yläosaa, kunnes tukijalustat irrotetaan, kääntämällä kantta 90° ja liu'uttamalla jalusta (3) jalustaan (6), saadaan korkea ruokapöytä.
Kuva 5. Sohva-ruokapöytä olohuoneeseen. Koostuu pöytälevystä (1); pohjalevy (2); kaapit (3) kiinnitettynä pöytätasoon 1; kaapin 3 tukikisko (4); jäykistepalkki (5); pohjalevyyn 2 kiinnitetyt kaapit (6); tukikisko (7) kaappi 6
Kahvi- ja ruokapöydän muotoilu on paneeli, kaikki elementit kiinnitetään tapilla ja liimalla. Tämän esineen tekeminen olohuoneen sisustukseen vaatii tarkat mittaukset, on erityisen tärkeää säilyttää kaapien mitat. Lisäksi tulee kiinnittää huomiota niiden säleiden (7) liitoksen lujuuteen, joiden päällä kaappi (3) lepää.
Puutarhan taitettava pöytä näyttää orgaanisesti kesämökin puiden varjossa, katoksen alla tai huvimajassa tehden samalla levosta mukavan ja mukavan. Tämän mallin valtava etu on sen tiiviys taitettuna ja erityinen lämpö, joka tulee omin käsin tehdyistä esineistä. Kuka tahansa voi tehdä taitettavan pöydän kesämökille, varsinkin kun työprosessi ei vaadi erityisiä työkaluja ja rakenteen materiaalia voi ostaa miltä tahansa rakennusmarkkinoilta.
DIY taitettava pöytä. Kuva
Tee itse taitettava piknikpöytä. Askel askeleelta kuvia
Ennen kuin aloitat kokoontaitettavan pöydän kokoamisen, muista, että puolet menestyksestä on käytössä laadukkaat materiaalit. Puussa ja levyssä tulee olla mahdollisimman vähän oksaa, eikä puun halkeamia ja irtoamista sallita. Puutavaran lisäksi tarvitset kiinnikkeitä, saranoita ja keinoja suojata puutavaraa ilmakehälle.
Pöydän tekemiseen tarvittavat materiaalit
Taitettavan pöydän valmistamiseksi sinulla on oltava käsillä:
- puutavara, mitat 45×45 mm - 8 kpl. 730 mm pitkä - jalkojen valmistukseen;
- säleet 45x20 mm: 2 x 550 mm ja 2 x 950 mm - pöydän yläkehyksen kokoamiseen sekä 2 x 350 mm - taitettavalle osalle;
- vanerilistat 40x27 mm tuille - 3 x 450 mm;
- 18 mm vaneri, jonka mitat: - 985x585 - arkki pöytälevylle - 2 arkkia 985x530 taitettaville osille - 1 arkki 885x481 mm hyllylle;
- kisko 440×40 mm poikkipalkkina;
- 2 sälettä 450x40 mm sivutukielementeille;
- 4 silmukkaa 60×34 mm pöytäliinojen kiinnitykseen;
- 4 silmukkaa 80x41 mm jalkojen taittumista varten;
- ruuvit galvanoidusta tai ruostumattomasta teräksestä;
- metalliset tapit hyllyjen kiinnittämiseen.
Kun leikkaat työkappaleita, yritä varmistaa, että kaikkien osien kulmissa ja niiden päissä on suorat kulmat. Käytä tätä varten puusepän neliötä, ja jos se puuttuu, voit käyttää tehdasleikatun levymateriaalin kulmaa.
Tee itse taitettavat pöytäpiirustukset. Kuva
Kokoamisohjeet
Ennen kuin aloitat taitettavan pöydän kokoamisen omin käsin, sinun on tehtävä se valmistella puuosat asennusta varten. Tätä varten jokaiseen runko-osaan leikataan enintään 20 mm leveä ja syvä ura työkappaleen keskelle (22,5 mm). Sama etäisyys mitataan reunasta uraan - 30-40 mm.
Vaiheittainen valokuva taitettavan piknikpöydän tekemisestä
Kun kaikki urat on leikattu, poraa reikiä osien liittämiseen yhteen sekä jalkojen kiinnittämiseen.
Jotta kehys ei vääristy, kun teet taitettavan pöydän omin käsin, tee a poikkileikkaukset, joka sisältää rungon kulmat asennuksen aikana. Tätä prosessia voidaan tarkastella yksityiskohtaisemmin esitetyissä kuvissa.
Oikein valmistetut osat ovat avain laadukkaaseen kokoonpanoon, joten on suositeltavaa käyttää korkealaatuisia laitteita - hyvää pyörösahaa, poraa, talttasarjaa ja muita puusepän työkaluja.
Yläkehyksen kokoaminen alakehykset(yleinen nimi pöytälevykehykselle). Tätä varten säleet kootaan uraan ja kiinnitetään huonekaluvahvistimilla (kuusioavaimen ruuvit);
Asennetaan koottuun runkoon tukijalat, yhdistämällä sahatut osat runkolistoihin.
Vanerihyllyn kulmissa he tekevät leikkaukset tukia varten. Kiinnitä laatta asentamalla jalat 220 mm etäisyydelle jalkojen reunasta. metalliset tapit.
Sisäänvedettävät tukielementit kootaan. Tätä varten loput tangot yhdistetään pareittain uriin asennetuilla säleillä kiinnittäen liitoskohdat vahvistuksilla.
Kun pöytälevy ja muut osat on hiottu ja pohjamaalattu, he alkavat maalata jalkatukea, säleitä ja pöytälevyä.
Kiinnitä hyllyn välike. Sivulistat on kiinnitetty pöytälevyn runkoon. Tukikiskot on kiinnitetty hyllyyn, jota varten siihen porataan reiät. Muista, että tämä työ vaatii erityistä huolellisuutta, sillä pienetkin siirtymät voivat vaikuttaa pöydän geometriaan.
Pöydän runkoon asennetaan jumpperi, jonka jälkeen kiinnitetään kolme ylimääräistä välikappaletta.
Sisäänvedettävät jalat Ne on saranoitu ja kiinnitetty ulkoisiin tukiin.
Pää- ja taittoosat pöytälevyt ruuvattu saranoihin.
Pöydän kansi on asennettu kehys, jonka jälkeen keskiosa kiinnitetään runkoon itsekierteittävillä ruuveilla.
Ohjeidemme mukaan koottu pöytä on riittävän luja ja luotettava. Tärkeintä on suorittaa työ askel askeleelta esitetyssä järjestyksessä. Käsittely ja maalaus on suoritettava ennen asennusta. Muuten yksittäisiä osia ei voida maalata huolellisesti, eikä lopputuote näytä tarpeeksi tyylikkäältä ja vaikuttavalta.
DIY muuntajapöytä. Ohjeet
Liukupöydällä on kestävä, vakaa muotoilu ja aloittelijakin selviää sen kokoamisesta. Taitettuna pöytälevyn mitat ovat 1200x700 mm. Kun pöytälevy on liu'utettu erilleen, tuloksena olevaan aukkoon asennetaan erityinen sisäosa, jolloin pöytälevyn pituus on 1670 mm. Tämä mahdollistaa lisäksi kahden aikuisen sijoittamisen pöytään.
Työkalut ja materiaalit
Ennen kuin menet rakennusmarkkinoille, kirjoita ylös, mitä osia ja materiaaleja tarvitset liukuvalla pöydällä varustetun pöydän kokoamiseen:
- laminoitu lastulevy 25 mm paksu;
- PVC-nauha jopa 2 mm paksuisten reunojen liimaamiseen;
- alumiiniset kulmat 50×50 mm - 4 kpl. 500 mm kukin;
- teleskooppiohjaimet laatikoille, pituus 500 mm - 2 kpl;
- huonekalujen jalat, joiden halkaisija on yli 60 mm - 4 kpl. pituus 710 mm;
- laatikon salpa - 6 kpl;
- 10 mm M4 kierreruuvit;
- huonekaluruuvit 16×3 mm ja 20×4 mm.
Työskennelläksesi sinun on valmisteltava seuraavat laitteet ja työkalut:
- jyrsin;
- sähköinen palapeli, jossa on sahat vanerille ja lastulevylle (hienot hampaat);
- pyörösaha;
- sähköpora ja poraporasarja;
- ruuvimeisseli tai ruuvimeisselisarja;
- rakennushiustenkuivain tai silitysrauta;
- tapetti veitsi;
- kupla taso;
- puristimet;
- mittaustyökalu, lyijykynä.
Ennen kuin aloitat materiaalin leikkaamisen, piirrä pöydästä mittojesi mukainen piirustus tai käytä ehdottamaamme mallia. Tässä tapauksessa pöytäkannen komponenttien mitat on ilmoitettu esitetyissä piirustuksissa.
Muunnettava pöytä. Piirustukset
Ohjeet taitettavan pöydän tekemiseen
Vaihe 1. Tehdä merkintä arkkimateriaalia, leikkaa sitten laminoidusta lastulevystä pöytälevyn osat - sisäke, jonka mitat ovat 700x470 mm, sekä kaksi pöytäkannen puolikasta, joiden mitat ovat 700x470 mm. Voit välttää lastulevyn pinnan halkeilua käyttämällä pistosahaa, jossa on erityisviila matalaprofiilisella hampaalla. Lisäksi leikkauskohtaan voidaan kiinnittää maalarinteippiä, joka estää pintakerroksen halkeilun.
Muista: jos aiot työstää työkappaleita jyrsimellä, varmista, että työstövara on vähintään 2 mm.
Laatan tasaiseksi leikkaamiseksi se kiinnitetään puristimilla työpöytään ja reuna tasataan. Työkalua tulee käyttää hitaasti ja tarkkailla jatkuvasti leikkauksen laatua.
Vaihe 2. Trimmaus reitittimen avulla voit saada täysin sileät sivupinnat. Tätä työkalua käytetään myös hitaasti ja huolellisesti.
Vaihe 3. Liitä pöytälevyn päät PVC-reunoilla. Työkappale kiinnitetään puristimella, leikataan pois ja reuna asetetaan laatan sivupintaan. Tämän jälkeen se lämmitetään hiustenkuivaajalla tai silitysraudalla ja tasoitetaan. Materiaalin kovettumisen jälkeen reunan ulkoneva reuna leikataan tapettiveitsellä pois.
Vaihe 4. Kaikki alumiinikulmien terävät reunat ja kulmat on käsitelty.
Muuntajapöydän teko. Kuva
Vaihe 5. Merkitse jokaiseen kulmaan keskikohta ja mittaa 25 mm jokaisesta reunasta.
Vaihe 6. Huonekaluohjaimien kumpikin puoli on kiinnitetty kulmaan ja niiden kiinnityspaikat on merkitty. Kulmat porataan määrätyissä kohdissa. Poran liukumisen estämiseksi alumiinin päällä asennuspaikat on hylsytetty. Kulmat ja ohjaimet on yhdistetty pulteilla.
Vaihe 7. Tuloksena olevat opasmallit makaamaan tasaiselle alustalle seuraavasti: sisäohjaimiin yhdistetyt kulmat (ohuet) asetetaan sisäänpäin, toisiaan kohti ja kulmat, joihin ohjainten ulkoosat on kiinnitetty (kiinteät, paksummat), sijoitetaan ulospäin. Tämän jälkeen liikkuviin ja kiinteisiin alumiiniosiin porataan 4 reikää.
Vaihe 8. Molemmat puolikkaat pöytälevyt aseta alaspäin työpöydälle tai muulle tasaiselle pinnalle. Päälle, 80 mm etäisyydelle paneelien sivuista, asennetaan sisäänvedettävät ohjaimet (liikkuva, ohut osa sisäänpäin). Tässä tapauksessa pöytälevyn puoliskojen välisen liitoksen tulee osua kunkin ohjaimen keskelle.
Vaihe 9. Teleskoopin kiinteä puolisko opas Ne on kiinnitetty pöytäkannen vasempaan puoliskoon ja liikkuva sen oikealle puolelle. Käytä tätä varten 20x4 mm itsekierteittäviä ruuveja.
Vaihe 10. Salvat ja saranat asennetaan liukujärjestelmän viereen.
Vaihe 11. Kun salvat ovat auki, siirrä pöytälevyn molemmat osat erilleen ja aseta lisää paneeli. Tämän jälkeen kaikki pöydän päällyksen elementit siirretään tasaiseksi, rakottömäksi pinnaksi.
Vaihe 12. Pöytälevyn keskiosaan on asennettu lisäsalpasilmukoita. Tuloksena oleva kiinnitys mahdollistaa pöydän kiinnittämisen sekä avoimessa että koottussa tilassa.
Vaihe 13. Jalat kiinnitetään pöytälevyyn 20 mm:n itsekierteittävillä ruuveilla.
Kun olet koottu taitettavan pöydän omin käsin, muista tarkistaa suunnittelu vahvuus ojennetussa ja taitetussa asennossa. Vasta testauksen jälkeen pöytä voidaan katsoa käyttökelpoiseksi ja asennettuna pysyvään paikkaan.
Maidonvärinen muunneltava ruokapöytä vieraille
Pienessä asunnossa huonekalut, kuten muunnospöytä, ovat korvaamattomia. Se on helposti muunneltavissa kompaktista sohvapöydästä täysivaltaiseksi usean ihmisen ruokapöydäksi.
Sohvapöytä muuttuu helposti täysivaltaiseksi pöydäksi vieraiden viihdyttämiseen
Lue ohjeemme ja varmista, että muunnospöydän kokoaminen on hyvin yksinkertaista.
Ruokailu- ja kahvivaihtoehtoja mitoiltaan muunnettavalle pöydälle
Tarvittavat työkalut huonekalujen kokoamiseen
Muuntajan onnistuneeseen kokoamiseen tarvitset:
- Phillips-ruuvimeisseli tai ruuvimeisseli kiinnikkeineen;
- huonekalujen vasara;
- kiinnikkeet ja tarvikkeet sisältyvät toimituspakkaukseen.
Pöydän rungon ja sen jalkojen yksityiskohdat
Laatikko kiinnikkeillä ja kiinnikkeillä
Huolimatta huonekalumarkkinoiden monista tarjouksista, useimmille valmistajille prosessi koostuu seuraavista vaiheista:
Asunnon kokoonpano
Pöydän kulmajalkojen kokoaminen
Kaikki muunnospöydän jalat on koottu
Kahden puolikkaan kulmajalat yhdistetään ruuveilla tai epäkeskeillä. Samalla tavalla runko kootaan pitkistä ja lyhyistä laatikoista.
Yksityiskohtainen kotelon kokoonpanoprosessi
Ruuvaa jalat vartaloon ohjeen mukaan
TÄRKEÄÄ! Jaloihin ja sivuille tehdään erityisiä reikiä koko rakenteen hissin ja tasoitteen samanaikaista asennusta varten. Tarkista asennuksen jälkeen, sopivatko ne yhteen.
Koottu pohja jaloilla
Naula muoviset jalkatyynyt jalkojen alapäihin. Laatikoiden yläpäihin asenna iskunvaimentimet, jotka vaimentavat pöytätason iskua sitä taitettaessa.
Naulaamme kantapäätyynyt jalkoihin
Nostomekanismin asennus
Nostomekanismin asennuskaavio
Aseta nostin työasentoon. Voit tehdä tämän seuraavasti:
Kiinteät jouset muunnospöytämekanismin toimintaa varten
Mekanismi on rauhallisessa, laajentumattomassa tilassa
TÄRKEÄÄ! Taitettavalle pöytälevylle suunniteltujen pidikkeiden jalat ovat korkeammat kuin alarunkoon.
Mekanismi pöydän nostamiseksi yläasentoon
Työtasojen ja aluskehysten asennus
Työtason pienemmän osan asennus
Jalustan asentaminen suurelle osalle pöytälevyä
Ruuvaa kirjapöydän kannen alaläppä ja pohja kiinni pidintasoille. Asenna iskunvaimentimet pöytätason ulkopuolelle vaimentamaan iskuja pöytälevyä avattaessa. Taita nostojalat laatikkoon ulkopuolelta sisäänpäin. Se peitetään pöytälevyn pohjalla.
Kiinnitä pöytätason liikkuva yläosa
Aseta toinen puolisko päälle siten, että piilosaranoiden päätyreiät ovat toisella puolella ja niiden keskipisteen välinen etäisyys on minimaalinen (noin 14 mm). Aseta saranat varovasti paikalleen ja kiinnitä ruuveilla.
Piilotetut saranat pöydän kiinnittämiseksi koottuna
Kokoamasi pöytä kestää pitkään. Älä unohda kiristää sen kiinnitysliitoksia kerran vuodessa, puhdista pinta kuivalla pehmeällä liinalla tai erityisellä huonekalukiillotusaineella.
Kahviversio tai taitettu pöytä
Prosessi, jossa pöytä muutetaan sohvapöydästä vieraiden vastaanottopöydäksi
Ruokailuvaihtoehto tai kokoontaitettava pöytä
Video: Muunnettava pöytä. Kokoonpano