Layout ng frame house 9 9. Kumportableng frame house sa isang palapag
(i-click ang proyekto para palakihin)
Ang isang alternatibo sa pagtatayo ng bahay mula sa isang bar o isang log ay ang pag-install ng isang gusali ng tirahan gamit ang teknolohiya ng frame panel. Upang gawin ito, maaari kang pumili ng isang proyekto kuwadrong bahay 9 × 8 turnkey na may iba't ibang mga finish at pagkakabukod.
Lugar ng bahay hanggang 150 sq.m. Ang facade ay kaakit-akit salamat sa panlabas na terrace at isang loggia sa ikalawang palapag, pati na rin ang isang kawili-wiling pagsasaayos may balakang na bubong... House 9 × 8 frame na may iba't ibang opsyon para sa mga presyo, finish at configuration. Maaari kang mag-order ng konstruksiyon mula sa aming mga espesyalista sa website, ang halaga ng konstruksiyon ay may bisa.
- Proyekto: K-4
- Mga sukat: 9 × 8 m
- Pagkumpleto ng "Dachny":
- Imitasyong timber finishing (lining, insulation 100mm): 915.000 kuskusin
- Tinatapos ang imitasyon ng isang log (block house, insulation 100mm):1.052.000 kuskusin
- Siding finish: sa kahilingan
- Pagkumpleto "Para sa permanenteng paninirahan"
- Pagtatapos imitasyon ng troso (lining, insulation 200mm): 1.058.000 kuskusin
- Tinatapos ang imitasyon ng isang log (block house, insulation 200mm): 1.134.000 kuskusin
- Siding finish: sa kahilingan
Lalo na para sa kaginhawaan ng customer, nakabuo kami ng dalawang kumpletong set ng bahay: "Dacha" at "Para sa permanenteng paninirahan" at kasama ang iba't ibang mga pagpipilian matatapos. Pinapayagan nito ang kliyente na piliin ang pinakamainam na pagsasaayos para sa kanya, ang uri ng pagtatapos at, pinaka-mahalaga, mag-order ng bahay sa loob ng balangkas ng kanyang badyet sa pagtatayo.
Pagkumpleto ng bahay na "Dachny"
Foundation: | V pangunahing bersyon nakalagay ang bahay kolumnar na pundasyon... Posibleng opsyon sa pundasyon: pile-screw at tape (kinakalkula nang hiwalay) |
---|---|
Strapping | Beam 150x150 mm. |
Mga pagkahuli sa sex: | Beam 100x150 mm, pagkatapos ng 70 cm. |
Mga pader ng 1st at 2nd floor: | Mga pader ng frame, mga rack na 100 × 50 mm bawat 60 cm (naka-mount sa mga sulok at mga kuko), jibs 100 × 50 mm. |
Nagpapatong: | Mga floor beam 150 × 50 mm bawat 50 cm. |
Mga partisyon: | Frame, rack 100 × 50 mm bawat 60 cm, jibs 100 × 40 mm. |
Pagkakabukod ng pader: | Pagkakabukod ng mga dingding at kisame na may pagkakabukod ng roll na "KNAUF" (at mga analog), 100mm ang kapal. |
Pagkakabukod ng mga partisyon: | Pagkakabukod ng mga partisyon na may pagkakabukod na "KNAUF" (at mga analog), 50mm ang kapal. |
Barrier ng singaw: | Isospan steam at wind insulation. Ito ay inilatag sa magkabilang panig sa mga dingding, partisyon, sahig at kisame. |
Panloob na sulok: | Ang isang plinth ay ipinako sa lahat ng mga joints ng kisame, dingding at sahig |
Bintana: | Kahoy na may double glazing, na may mga kabit, cashed, laki 1.0x1.2 m. |
Mga pintuan: | Pagpasok - metal. Paneled, cashed, walang mga kabit, 2x0.8 m ang laki. |
Rafter: | Mga rafters mula sa isang board na 100x50mm. na may hakbang na hindi hihigit sa 1.0 m. |
bubong: | Ondulin (opsyonal: pula, berde, kayumanggi). |
Sheathing: | Edged board 20x100 (150) mm, ang lathing ay gawa sa edged board na 20 mm ang kapal na may pitch na hindi hihigit sa 400mm |
palapag: | Doble: magaspang - may talim na tabla 20 mm. (ito ay umaangkop sa isang tuloy-tuloy na linya), Finishing - tongue-and-groove board 28 mm, na may isospan steam at waterproofing at KNAUF insulation (100 mm). |
Taas ng kisame: | 1st floor - 2400 cm; 2nd floor - 2300 cm. |
Pagtatapos | Lining (imitasyon ng bar) (kapal 12.5-16mm.) Block house (imitasyon ng log) kapal (28-34mm) |
hagdan: | Kahoy na hagdanan patungo sa ikalawang palapag, isang martsa na may mga rehas at balusters mula sa lining |
Cornices: | Ang mga cornice, celestial wall ay natatabingan ng clapboard. Mga overhang ng bubong na hindi bababa sa 20cm |
Mga Platband: | Platbands para sa bintana o mga pintuan sa magkabilang panig |
Panlabas na sulok: | Ang mga sulok ng dingding sa labas ay natatakpan ng mga platband |
Mga post sa sulok: | Mga poste sa sulok 100 × 100mm |
Pagkumpleto ng bahay "Sa ilalim ng permanenteng paninirahan"
- Karagdagan ay kinabibilangan ng:
- 1. Naka-on ang pagkakabukod ng pader 200mm. (sa halip na 100mm)
- 2. Wall frame timber 200 × 50mm(sa halip na 100 × 50mm) pagkatapos ng 60cm.
- 3. Idinagdag mga counterracks(Ang pag-install ay nasa vapor barrier sa loob, ang materyal sa pagtatapos ay tumatakbo na sa kanila) Layunin: upang lumikha ng karagdagang agwat ng hangin na tumataas mga katangian ng thermal insulation mga pader.
- 2. Pagpapatong ng kahoy sa ikalawang palapag 150 × 100mm sa pamamagitan ng 60cm. (sa halip na board 150 × 50mm)
- 3. Board floor dila 36mm... (sa halip na 28mm)
- 4. Taas ng kisame: 1st floor 2600cm.(sa halip na 2400cm.), 2nd floor 2500cm.(sa halip na 2300cm)
- 5. Idinagdag ang vapor barrier Isospan sa ilalim ng bubong.
- 6. Ang mga bintana ay naka-install windowsills gawa sa kahoy at sa labas ebb.
- 7. Corner drains 200 × 150mm
Ang kumpletong hanay na "para sa permanenteng paninirahan" ay pinili sa paraang magpapahintulot na manirahan sa bahay sa pagtatapos ng konstruksiyon nang kumportable sa buong taon.
Nag-aalok kami ng tatlong mga opsyon para sa pagtatapos ng mga frame-panel house:
1. imitasyon ng troso (lining)
2.imitasyon ng isang log (block house)
3.panghaliling daan
- Pakipili
- Pakipili
- Pakipili
- Pakipili
- Pakipili
- Pakipili
- Pakipili
Tignan ang detalye
Tingnan ang mga detalyadong sagot sa mga madalas itanong tungkol sa konstruksiyon
Larawan sa pamamagitan ng konstruksiyon mga kuwadrong bahay
Ang mga frame house ay nagsimulang itayo higit sa isang daang taon na ang nakalilipas, at mula noon ang kalidad ng mga materyales ay nagbago nang malaki. Gayunpaman, kahit na isinasaalang-alang ang katotohanan na sa siglo bago ang huling, ang mga smallpox slab ay hindi ginamit upang bumuo ng mga pader, ang mga gusali ay matagumpay na nakapasa sa pagsubok ng oras. Moderno kuwadrong bahay 9x11, ang gastos nito ay maaaring mag-iba mula sa 1,000,000 rubles sa mas mababang bahagi ng threshold ng presyo, ay ginagarantiyahan na tatagal nang hindi bababa, dahil ang mga panahon ng pagpapatakbo na inilaan ng GOST para sa mga smallpox plate at ang frame mismo ay katumbas ng isang siglo.
- Mga sukat ng bahay: 9 x 11 m
- Kabuuang lawak: 198 m 2
- Presyo: 2 739 400 kuskusin
- Mga sukat ng bahay: 9.6 x 11.3 m
- Kabuuang lawak: 217 m 2
- Presyo: 2 942 100 kuskusin
Ang tanging "mahina na link" sa buong konstruksiyon ay pagkakabukod. Dapat itong baguhin tuwing 30-40 taon, dahil mas mahabang panahon mineral na lana ay hindi nagpapanatili ng mga katangian nito. Gayunpaman, bago piliin ang iyong proyekto, hindi pa rin magiging labis na malaman kung ano ang mga pakinabang ng frame kumpara sa iba pang mga materyales.
Paano naiiba ang isang 9x11 frame house mula sa isang brick o kahoy
Karaniwan silang pumili sa pagitan ng tatlong pangunahing uri ng konstruksiyon, ang pinakasikat hindi lamang bilang mga suburban: batay sa mga frame, mula sa mga brick, mula sa troso. At ang bawat isa sa mga materyales ay may sariling mga pakinabang. Ang klasiko ng genre ay kahoy, ito ay aktibong ginagamit mula pa noong unang panahon, nang ang mga troso ay na-fasten sa mga grooves at ang isang bahay ay itinayo nang walang isang solong pako, hindi alam kung ano ang pakiramdam ng pagtatrabaho sa mga turnilyo o iba pang mga fastener. Mga bahay na gawa sa kahoy mula sa isang bar ay tinatawag na pinaka-friendly na kapaligiran at mayroong ilang katotohanan sa ito, dahil ang puno mismo ay isang natural na materyal.
Gayunpaman, kung susuriin mo kung saan itinayo ang 9x11 frame house, makikita mo na parehong ligtas para sa kalusugan ang mga plato ng bulutong at cotton wool na ginamit bilang insulasyon. Samakatuwid, mula sa pananaw ng ekolohiya, ang mga frame house ay hindi mas masahol pa. Kung pipili ka sa pagitan ng kahoy at mga frame, kailangan mong tandaan na ang puno ay nangangailangan ng pag-urong. Karaniwan, ang mga timber at plank house ay itinatayo sa loob ng ilang taon, habang ang isang 9x11 frame house na nakabatay sa isang frame at smallpox sheet ay maaaring makumpleto sa loob ng ilang buwan. Ang mga tubo, iba pang komunikasyon at panloob na dekorasyon ay isinasagawa sa isang tuluy-tuloy na ikot ng konstruksiyon.
Kung pipiliin mo sa pagitan ng mga frame house at brick, magiging malinaw na walang duda tungkol sa lakas at pagiging maaasahan ng pangalawa. Gayunpaman, para maging mainit ang isang bahay, dapat itong magkaroon ng sapat na mga pader. Isinasaalang-alang ang medyo mataas na halaga ng mga brick, ang mga gastos ay halata, at para sa halagang 1,000,000 rubles, kung saan maaari kang magtayo ng isang 9x11 frame house, tiyak na hindi ka makakagawa ng isang brick. At isa pang plus sa gilid ng mga gusali batay sa frame ay ang all-season installation.
Brickwork sa mga sub-zero na temperatura imposible nang walang mga espesyal na additives sa solusyon, dahil masyadong mabilis itong tumigas. Imposibleng gawin nang wala ito, dahil nai-fasten nila at patuloy na ikinakabit ang pagmamason dito. Kasabay nito, kung ang pundasyon ay ibinuhos na malapit sa bahay, kung gayon ang pag-install ng frame mismo ay maaaring isagawa sa anumang mga kondisyong pangklima... Pati na rin upang isagawa ang strapping ng bahay, at magtrabaho sa dekorasyon nito.
Ano ang mga pakinabang ng isang 9x11 frame house
Ang pangunahing isa ay ang kakayahang mabilis na magpainit. Pansinin ng mga review ang katotohanan na kahit na ang isang bahay na lumamig sa mga hamog na nagyelo, na hindi pa ginagamit mula noong tag-araw, ay maaaring magpainit sa loob lamang ng ilang oras. Sa mga gusaling gawa sa mga brick o tabla, imposible ang pagpipiliang ito, anuman ang kapal ng mga dingding. Gayundin, ang mga frame house ay mabuti para sa:
- na sila ay magaan;
- walang malaki at mamahaling kagamitan ang kinakailangan para sa kanilang pagtatayo;
- walang monumental na mga slab ang kailangan upang punan ang pundasyon.
Ang kapal at bigat ng mga pader ay tulad na ang bahay ay madaling makatiis sa isang magaan na pundasyon. Ang mga pagtitipid sa kasong ito ay halata, habang hindi nakompromiso ang lakas ng buong istraktura. Samakatuwid, hindi mo dapat isipin na ang isang 9x11 frame house ay hindi gaanong maaasahan kaysa sa isang brick, o lamang bakasyon sa tag-init o katapusan ng linggo. Sa taglamig, ito ay hindi gaanong mainit at maaari itong makakuha ng higit sa demokratikong presyo mula sa 1,000,000 rubles pataas. Samakatuwid, ang gayong pabahay ay mabuti para sa mga nais makakuha ng isang buong taon na konstruksyon.
Mga alamat na nakapalibot sa 9x11 frame house
Ang mga hindi pa naka-install ng isang bahay sa batayan ng isang frame sa kanilang site ay madalas na marinig na, parang, maaari lamang itong pansamantala, dahil hindi ito nakatayo sa paghahambing sa mga tuntunin ng lakas sa isang brick. Sa katunayan, ang mga pader ng bulutong ay hindi gaanong matibay, pati na rin ang pundasyon, na maaaring hindi lamang monolitikong kongkreto, mga beam sa sahig at mga tabla sa sahig. Dahil ang isang bahay ng mga baraha tulad ng isang bahay ay hindi kailanman mabubuo, maaari itong makatiis kahit buhawi at lindol, pati na rin ang mga pader sa loob nito ay hindi masisipa. Huwag malito ang drywall at smallpox sheet, ang una ay talagang marupok, ngunit ang mga plato ay hindi mas masahol pa kaysa sa mga tabla o troso, dahil ang mga ito ay nilikha mula sa basura. produksyon ng kahoy... Kaya't ang 9x11 frame house ay tatagal ng mahabang panahon, hindi sa banggitin na, sa pangkalahatan, ang mga pangako ng mga pagtatangka ng mga kriminal na basagin ang mga pader upang makapasok sa loob ng bahay ay hindi lohikal, kung mayroong mas maraming naa-access na mga bintana para dito.
Ang mga frame ay tinatawag ding nasusunog, ganap na nakakalimutan na hindi lamang mga dingding na gawa sa mga sheet ng bulutong ang nakalantad sa apoy. Ang puno ay nasusunog din, samakatuwid, sa mga tuntunin ng paglaban sa sunog ang pinakamahusay na mga katangian nagtataglay ng isang ladrilyo, gayunpaman ang mga bahay na gawa rito, gaya ng nabanggit na, ay mahal. Ngunit ang frame ay may sariling makabuluhang bentahe: ang drywall na ginagamit para sa panloob na dekorasyon ay hindi nasusunog, pati na rin ang lana bilang pagkakabukod, samakatuwid, kung ihahambing sa isang kahoy na frame house 9x11, ito ay magiging mas ligtas, lalo na kung ang puno ay hindi maayos. naproseso.
Kadalasan, bilang isang problema, ipinahiwatig na ang mga daga ay nagsisimula sa mga dingding ng mga frame house, dahil sa pagitan ng mga sheet, crate at pagkakabukod ay may isang uri ng lukab na puno ng pagkakabukod at waterproofing. Kasabay nito, tinutukoy nila ang katotohanan na para sa mga rodent mismo, ang parehong pagkakabukod at bulutong para sa mga dingding ay pantay na kaakit-akit. Ngunit sa ilang kadahilanan nakalimutan nila na hindi lamang ang 9x11 frame house, kundi pati na rin ang pabahay na gawa sa mga tabla, troso at kahit na brick mula sa mga daga ay hindi rin nakaseguro.
Kaya lang, sa huli, ang posibilidad ng kanilang pagtama ay isang order ng magnitude na mas kaunti, dahil ang kongkreto ay ginagamit upang lumikha ng pundasyon, at pagkatapos ay batay sila dito mga pader ng ladrilyo- napakahirap maghanap ng daanan para makapasok. Gayunpaman, ang problemang ito ay madaling maiiwasan kung, sa panahon ng pag-install ng pundasyon, ang isang fine-mesh mesh ay ginagamit sa paligid ng perimeter ng gusali. Sa ganoon, hindi tulad ng mga board, tiyak na hindi ka makakagat ng isang butas.
Kung ang pagpapatupad ng proyekto ay iniutos mula sa mga espesyalista, kung gayon sila, hindi bababa sa, ginagarantiyahan ang pagkakaroon ng isang malinaw na pamamaraan ng mga gastos, kung saan mayroong isang lugar para sa bawat maliit na bagay, simula sa kung magkano ang gastos upang sumang-ayon sa dokumentasyon sa BTI at nagtatapos sa kung anong mga turnilyo ang gagamitin para sa mga fastener. Ang bawat hakbang ay inireseta sa loob nito, dahil kapag nakita ng customer ang panghuling halaga sa catalog, na gagastusin sa pagtatayo ng isang 9x11 frame house, wala siyang duda na ito ay magiging pangwakas. Ang halaga ng konstruksiyon ay maaari lamang magbago kung gusto ng customer na gumawa karagdagang pagbabago sa proyekto. At ang mga iyon ay dapat teknikal na posible, hindi alintana kung ang bahay ay nagkakahalaga ng 1,000,000 rubles o higit pa.
Paano ginagawa ang isang 9x11 frame house
Tulad ng anumang konstruksiyon, ang mga bahay na nakabatay sa frame ay nangangailangan ng isang handa na lugar ng pagtatayo. Dapat ay walang mga pagkakaiba sa pagitan ng mga antas ng taas sa ibaba at tuktok na bahagi, kung ang lupa ay tiyak, ang geodesy ay tinatanggap din, dahil ang pagpili ng uri ng pundasyon ay nakasalalay sa kalidad ng lupa. ang pundasyon, depende sa napiling uri, ay ibinubuhos kongkretong mortar... Kapag naitatag ng mga manggagawa ang pundasyon para sa hinaharap na bahay sa isang antas, tatagal ng hindi bababa sa dalawang linggo para ganap itong matuyo. Sa yugtong ito, mahalaga din na huwag kalimutan ang tungkol sa paggamit ng isang rodent net sa ibaba, na naayos din sa isang solusyon. Sa dulo ng pagbuhos ng pundasyon, ito ay itinayo nang mag-isa frame ng kapangyarihan, ngunit bago ito pumasa sa entablado ilalim strapping sa bahay.
Para dito, ang isang sinag o mga board ay na-install sa pundasyon. Sa kurso ng mas mababang strapping, natatanggap ng 9x11 frame house ang batayan nito, dahil dapat itong maayos sa pundasyon mismo. Kung hindi, ang frame ay walang dapat panghawakan. Ang mga board ay nakakabit kasama ng mga espesyal na metal bracket o sulok. Kapag ang mga detalye ng mas mababang strapping ay na-install at isinara, sa hinaharap, ang mga board ay gagamitin upang lumikha ng pahalang na strapping, ang sahig, dahil ang mga dingding at partisyon ay gawa sa mga slab. Ang mga board ay nakakabit sa patayong mga post gawa sa kahoy. Ang mga rack ay magiging "balangkas" ng hinaharap na bahay at ang mga pader ng bulutong ay naayos sa kanilang base, maaari silang itayo sa anumang panahon. Ang distansya sa pagitan ng mga post ay ginawa nang napakahaba na maaari itong pantay na maipamahagi at makatiis sa mga pagkarga sa hinaharap.
Kapag ang pundasyon at mga rack ng frame house ay handa na, ang trabaho ay isinasagawa upang ihanda ang sahig bago magpatuloy sa pag-install ng mga dingding. Para sa kanya, ang mga manggagawa ay nag-install ng mga log, ang distansya sa pagitan ng kung saan ay hindi hihigit sa 60 cm, na isinara ang mga board o sheet. Ito ay isang magaspang na pagtatapos ng sahig, kung saan ang isang puting tapusin ay isinasagawa. Para sa mga istrukturang nagdadala ng pagkarga ang mga materyales na ginamit para sa mga dingding at sahig ay pareho, pinapayagan ka nitong protektahan ang 9x11 frame house mula sa mga posibleng pagbaluktot. Sa ibabang bahagi, ang mga ito ay pinagtibay ng mga anchor, glassine at pagkakabukod ay inilalagay sa ibabaw ng subfloor, at pagkatapos ay ginagamit ang mga naprosesong board o sheet, kung saan maaari kang maglatag ng parquet, linoleum, o simpleng pintura.
Bilang karagdagan sa mas mababang strapping, ang mga dingding ng frame house ay nagbibigay din para sa itaas. Nakumpleto niya ang yugto ng pagtayo ng frame mula sa sahig hanggang sa kisame. Sa mga lugar kung saan ito nakaplano panloob na mga partisyon, nakalagay ang mga hiwalay na post ng suporta, naka-attach sa mga beam sa kisame o mga bakal na bracket, o koneksyon sa uka. Ang mga pagbubukas ng bintana at pinto ay na-install din sa yugtong ito. Kailan mga slab sa kisame handa na, under construction sistema ng rafter... Para sa kanya, ang mga board ay hindi angkop at ang isang sinag ay ginagamit bilang isang base, katulad ng para sa paglikha ng isang rack. Ang pag-install ng bubong ay nangangailangan ng espesyal na karanasan sa trabaho at ang pagtatayo nito mismo ay mas mahirap kaysa sa paggawa ng isang frame.
At ang punto dito ay hindi lamang na ang trabaho sa mga rack ay hindi madali, ang bubong ay nangangailangan ng init at waterproofing, kung wala ang 9x11 frame house ay hindi magiging komportable. At lamang kapag ang bubong ay sarado at ang pagkakabukod ay na-install, ang bahay ay nababalutan ng bulutong na mga sheet mula sa labas, tapos sa labas na may panghaliling daan o iba pa. materyal sa pagtatapos... Kung ang mga kaukulang mga ay naayos nang tama, gamit ang naaangkop na mga fastener para sa sahig at bubong, at hindi limitado sa mga kuko at mga turnilyo, kung gayon ang gusali ay hindi magiging sanhi ng anumang mga reklamo. At kapag ang mga sheet ng pagkakabukod ay inilatag, ang waterproofing sa honey ay isinasagawa gamit ang mga rack, pagkatapos ay maaari kang magpatuloy sa panloob na pagkakabukod pader at mga gawaing pang-inhinyero.
Ang mga tubo at iba pang komunikasyon ay mapagkakatiwalaang nakatago sa pagitan ng mga sheet ng drywall at bulutong. At halos mas mahirap mag-install ng mga panloob na komunikasyon kaysa sa pag-fasten ng mga sheet. Hindi mahalaga kung ito ay mga tubo ng pag-init o mga tubo ng suplay ng tubig, mga kable ng kuryente o dumi sa alkantarilya. Summing up, ang konklusyon ay nagmumungkahi mismo na ito ay lubhang mahirap na bumuo ng isang 9x11 frame house sa iyong sarili, dahil ang mga serbisyo ng mga propesyonal ay hindi isang luho. Handa na kaming magtayo ng mga bahay batay sa isang frame sa loob maikling oras... Posible talagang pumili ng opsyon na magkakahalaga sa loob ng 1,000,000 rubles.
Sa taglamig, ang mga site ng konstruksiyon ay nakatayo pa rin, oras na upang maghanda para sa pagtatayo ng tagsibol, mangolekta ng impormasyon, pag-isipan ang mga proyekto, gumawa ng mga desisyon sa kung anong teknolohiya at kung anong teknolohiya ang magsisimulang magtayo sa tagsibol, at ito ay hindi malayo.
Noong nakaraang taon, sa forum na ito, sinabi ko kung paano kami nagtayo ng aking kapatid frame bath... Ngayon gusto kong ipakita sa iyo ang isang ulat na may mga larawan at mga paliwanag. proseso ng pagtatayo kuwadrong bahay. Umaasa ako na maraming mga kalahok sa forum, na bubuo sa kanilang sarili, ay matuto ng isang bagay na kawili-wili at kapaki-pakinabang para sa kanilang sarili. Ito ay tungkol sa pagtatayo ng bahay na ito:
Marami sa inyo ang bumibili at nagbabasa ng mga magazine ng DOM, sa ikalawang isyu ng taong ito ay may artikulo tungkol sa kung paano sa ilang holidays at isang summer vacation ang aming kaibigan ay nakapagpatayo ng ganoong bahay. Sa opisina ng editoryal ng magasin, ang tekstong inihanda ko ay nabawasan ng kaunti, ang ilan sa mga litrato at mga guhit ay tinanggal, ngunit gayunpaman, sa tingin ko ang teknolohiya ng konstruksiyon ay malinaw sa marami.
Dito ko ihaharap sa iyong atensyon buong teksto kasama malaking halaga mga larawan, susubukan kong sagutin ang iyong mga katanungan, huwag lamang makipag-ugnay sa akin bilang isang propesyonal na tagabuo, pareho ako ng karamihan sa iyo, masaya akong sasabihin sa iyo ang tungkol sa lahat ng mga subtleties, lahat teknolohikal na proseso ginamit ko sa pagtatayo ng mga frame house.
Nagpasya na magtayo maliit na bahay sa teknolohiya ng frame, para sa gayong istraktura, maaari kang gumamit ng isang haligi na pundasyon, na hindi kukuha ng maraming oras at pagsisikap, at maaari mong itayo ang frame ng naturang bahay sa ilalim ng bubong nang walang panloob na dekorasyon sa loob ng ilang araw.
Proyekto. Ang pamilya ng may-ari ng bahay ay binubuo ng apat na tao, na nangangahulugan na ang bahay ay dapat magkaroon ng hindi bababa sa tatlong silid-tulugan, isa malaking kwarto para sa mga bisita, kusina, toilet room na may shower, malaking terrace para sa evening tea at kainan nasa labas... Isang tipikal na country house ng isang pamilya na may average na kita. Sineseryoso nila ang pagpapaunlad ng proyekto sa bahay, dahil hindi lamang ang isyu ng kaginhawaan ng bahay sa pagpapatakbo ay nakasalalay dito, kundi pati na rin ang presyo ng bahay, ang teknolohiya ng konstruksiyon at ang oras na kinakailangan upang magtayo at makagawa ng panlabas at panloob na dekorasyon sa bahay.
Sa una, pinlano na gumawa ng dalawang bay window upang ang bahay ay magkaroon, tulad ng sa amin, hindi pangkaraniwan. hitsura... Ngunit sa proseso ng pagtatrabaho sa mga guhit ng mga detalye ng frame, sila ay dumating sa desisyon na walang bay window, oras ng konstruksiyon at mga gastos ay maaaring makabuluhang bawasan, at ang bahay ay magiging mas mainit at mas praktikal. Batay sa mga kundisyong ito at kanilang mga teknikal na kakayahan, gumawa ng isang proyekto sa bahay.
Pagpasok sa bahay sa pamamagitan ng terrace - 13m2, panahon ng taglamig taon, gagawin nito ang pag-andar ng isang malamig na vestibule, mula dito ay pumasa kami sa isang maliit na pinainit na koridor - 5m2, kung saan mayroong isang hanger para sa damit na panlabas at isang istante para sa mga sapatos. Mula sa koridor na ito maaari kang makarating sa silid-tulugan ng mga magulang - 11m2, silid ng palikuran- 6m2 at sa kusina - 18m2. Ang kusina ay binubuo ng dalawang zone, sa tabi pambungad na pintuan work zone may lababo na may work table, gasera, refrigerator at mga istante, may dining area na may malaking mesa, sulok na sofa at isang metal na fireplace na kalan, kung saan maaari kang makapasok sa silid ng panauhin-21m2 at mga silid-tulugan ng mga bata -8.6m2 at 10.8m2.
Pundasyon. Dahil napagpasyahan nilang itayo ang bahay na may magaan na one-story frame na teknolohiya, na may sukat na 11 sa 9 na metro, ang pundasyon ng bahay ay ginawa gamit ang isang haligi, gamit ang mga tubo ng asbestos-semento na puno ng kongkretong mortar. Ang nasabing pundasyon ay maaaring gawin nang napakabilis, at hindi na kailangang maghintay ng isang buwan hanggang sa ganap na tumigas ang semento.
Sa tulong ng isang benzo drill, ang mga butas na may diameter na 200 mm ay drilled sa lupa. sa lalim na halos isang metro. Ang distansya sa pagitan ng mga post ay 80-90cm.
Nag-install kami ng mga tubo ng asbestos-semento sa isang antas sa mga drilled hole na may panloob na diameter 100mm., 1.3m ang haba. Nagwiwisik sila ng buhangin sa paligid ng mga tubo, nagbuhos ng tubig at tinampal ito, nagbuhos ng kongkretong mortar sa mga tubo sa proporsyon: isang balde ng semento, apat na balde ng buhangin at lima hanggang anim na balde ng mga durog na bato. Sa mga tubo kung saan magpapahinga ang mga log sa sahig, ang mga espesyal na plato ay na-install para sa pag-fasten ng mga log.
Sa dalawang araw na bakasyon, 125 na tubo ang na-install at napuno ng kongkreto.
Ang mga balon ay na-drill sa lalim na halos isang metro.
Ang mga tubo ay na-install ayon sa antas at linya ng tubo, pagkatapos ay binuburan sila ng buhangin at na-thrombosed.
Ang mga tubo ay napuno ng kongkretong mortar sa pamamagitan ng isang espesyal na funnel.
Sa mga pista opisyal ng Mayo, mula Mayo 7-9, ang lahat ng mga tubo ng pundasyon ng hinaharap na bahay ay na-install at napuno ng kongkreto.
Presyo ng bahay na may pagkakabukod 200mm min. cotton wool at finishing 698t.r.
Presyo ng bahay na may pagkakabukod 200mm min. cotton wool, finishing at foundation 808t.r.
Presyo ng bahay na may pagkakabukod 200mm min. cotton wool, dekorasyon, pundasyon, electrics, plumbing at supply ng tubig 869t.r.
Standard insulation 200mm basalt min. cotton wool, presyo 250mm + 20t.r. sa mas mataas na presyo.
Presyo ng proyekto para sa pagpupulong sa sarili 14t.r. I-download ang pagtatantya at basahin
Kung, sa ilang kadahilanan, hindi mo nais o hindi maaaring magtayo ng isang bahay sa iyong sarili ayon sa aming proyekto, kung gayon magagawa namin ang lahat ng ito para sa iyo, at sa mura at sa pinakamaikling posibleng panahon, para sa higit pang mga detalye tungkol sa mga presyo at mga pakinabang ng pagtatayo ng turnkey , basahin ang seksyong "Price Full construction ".
Kumportableng frame house sa isang palapag.
I-download, Project KD-45 (super-comfort) 0.41 Mb (pdf) >>> Detalyadong Paglalarawan.Ang proyekto ng isang frame house 9 x 12m ay maliit, ngunit napaka komportable at komportableng tahanan para sa Permanenteng paninirahan... Ang bahay ay may boiler room para sa gas boiler at isang malaking banyo. Maaari kang magtayo ng gayong bahay sa iyong sarili, gamit ang iyong sariling mga kamay ayon sa aming mga guhit o sa pamamagitan ng aming sariling mga pagsisikap.
Ang dekorasyon ng bahay ay maaaring mabago upang umangkop sa iyong mga kagustuhan, ayon sa proyekto: panlabas na pagtatapos ng OSB at panloob maayos na pagtatapos Kasama ang GKL sa halaga ng proyekto. Gayundin, ang presyo ng proyekto ay may kasamang pundasyon, pagkakabukod 200mm min. cotton wool (posibleng hanggang 250mm), mga de-koryenteng kable at mga produkto ng pag-install, automation, supply ng tubig at alkantarilya na may naka-install na pagtutubero.
Isang palapag na bahay 108m 2: Taas ng kisame 2.8m, Silid-tulugan 13.2m2, Silid-tulugan 13.2m2, silid-tulugan ng mga bata 12.3m2, Kusina 15.3m2 Salas 15.3m2, Corridor 7m2, Boiler room 6.3m2, banyo 6 , 3m 2, Entrance 5,3m 2, Entrance 5,3m2, Entrance 5,3m2 2
Mga katulad na proyekto: KD-451 o KD-47 at KD-3 at KD-35 o KD-4 at KD-43 at KD-42 at KD-68Upang palakihin ang larawan, i-click ito.
1. Karaniwang opsyon.
Floor plan, 3D view.
Mga pagpipilian sa hitsura:
anumang pagtatapos ay posible, tingnan ang mga opsyon, proyekto KD-33, KD-34, KD-42, atbp.
Mga marka ng taas:
Foundation para sa bahay na ito:
ayon sa proyektong MZLF 50v x 40sh.
ang mga tambak ay posible (tornilyo, nababato, atbp.) mga tambak min. 32pcs, mas maganda 38pcs.
Sa pamamagitan ng pag-click sa mga larawan sa ibaba, makikita mo ang mga gallery ng larawan ng mga bahay na itinayo ayon sa proyektong ito ng aming mga tagabuo o ng aming sariling mga customer (tingnan ang tala sa mga gallery):
Ang average na market value ng naturang bahay ay 4 na beses na mas mataas kaysa sa amin.
Order ng proyekto
Upang makapag-order, piliin ang uri ng pundasyon at iba pang posibleng opsyon, pagkatapos ay i-click ang button na "Mag-order ng proyekto." Sa form na bubukas, ilagay nang tama ang iyong email at iba pang kinakailangang data. Kung nakumpleto nang tama ang order, pagkatapos ay kaagad pagkatapos maproseso ng aming espesyalista ang order, makakatanggap ka ng kumpirmasyon ng order sa pamamagitan ng koreo na may paglilinaw ng mga detalye at mga opsyon sa pagbabayad.
Proyekto KD-45
Tape (MZLF) Piles
Presyo ng proyekto 14t.r.
(isang set ng mga working diagram at assemblies: frame house, foundation, electrical engineering, estimate, atbp.)
Mag-order ng isang proyekto
Mga madalas itanong mula sa mga customer:
Paano kung kailangan mong baguhin ang isang bagay sa isang proyekto na gusto mo?
Ang ideya ng pagtatayo ng isang cottage ng tag-init ay mahaba at matatag na nananatili sa aking ulo, ako ay naghahanap at nagtatrabaho nang mahabang panahon iba't ibang mga pagpipilian, ngunit perpektong solusyon para sa akin ay isang 6x9 frame house.
Nagustuhan ko ang proyekto ng bahay at ang mga guhit na nakalakip dito, una, para sa kaginhawahan ng layout ng pabahay, at, pangalawa, para sa paghahambing na pagiging simple ng trabaho. Marami kang magagawa gamit ang iyong sariling mga kamay, na inaasahan ko, dahil ako ay pangunahing magtatayo sa aking sarili. Ang pagtatayo ng bahay ay isinasagawa sa mga yugto, at, mahalaga, ang pagtatayo ng frame ng bahay ay hindi partikular na kasama mga kumplikadong elemento at mga detalye.
Ang tanging pagbabago ng proyekto sa aking bahagi ay ang pagbabago sa materyal ng cladding ng bahay na may Mga sheet ng OSB sa mas modernong mga panel ng ISOPLAAT, bilang isang resulta kung saan ang distansya sa pagitan ng mga post sa frame ay bahagyang nagbago bahay ng bansa.
Paglalagay ng pundasyon ng isang 6x9 frame house
Isa at kalahating palapag na frame house 6x9 - sapat na magaan na konstruksyon at ang paggamit ng isang mababaw na pundasyon tape (MZFL) ay naging ang pinaka-kaugnay, simpleng upang maisagawa at matipid isang kumikitang solusyon... Ang isang layer ng durog na bato (20 cm) ay inilatag sa ilalim ng trench na 50 cm ang lalim, pagkatapos ay ang formwork ay binuo, ang reinforcement ay konektado at ang pundasyon ay ibinuhos. Ang lapad ng tape ay 30 cm, na medyo katanggap-tanggap sa mga napiling parameter.
Ang ilang mga layer ng materyales sa bubong na inilatag sa ibabaw ng tape ng pundasyon ay nagsilbing waterproofing. Sa bubong nadama ay inilatag - mga board na ginagamot sa antiseptikong "Senezh". Sa isang hakbang na 1.5 metro, ang mga tabla ay hinila sa pundasyon ng bahay sa tulong ng mga anchor.
Ang pagpupulong ng mas mababang palapag para sa isang 6x9 frame house ayon sa proyekto ay hindi nangangailangan malaking pagsisikap at mga gastos sa oras. Insulated ko ang istraktura na may Ecover basalt slab - tumagal ng 7.5 m3 ng mga slab na may density na 28 kg / m3. Pagkatapos nito, ginawa ang sahig ng isang grooved oriented strand board na may kapal na 18 mm.
Isinasaalang-alang ko na ito ang pinakamababang halaga para sa sahig, na may distansya sa pagitan ng mga joists na 50-60 cm. Kung ang iyong pamilya ay may mga miyembro na may sapat na malaking bigat ng katawan, inirerekumenda ko ang plywood o OSB na mas malaki ang kapal bilang sahig. Kung balak mong manirahan nang permanente sa bahay, pagkatapos ay ipinapayo ko sa iyo na ilagay ang mga log sa mas malapit na distansya - 40 cm, ito ay magpapataas ng lakas at tibay ng sahig.
Upang masubaybayan ang estado ng underground, nagbigay ako ng dalawang hatches.
Konstruksyon ng mga dingding ng isang 6x9 frame house ayon sa proyekto
Ang trabaho sa mga dingding ng 6x9 frame house ay nagsimula sa isang hindi kasiya-siyang sorpresa - ang tuyo, na binili ko sa 9.5 tr / m3, ay hindi ganoon kataas ang kalidad na tiniyak ng mga nagbebenta.
Nagpasya akong palakasin ang istraktura gamit ang mga braces - mabilis silang naka-install, at maraming benepisyo mula sa kanila. Ang mga lokasyon ng mga braces sa mga frame ng dingding ay pinili upang hindi sila mahulog sa mga pagbubukas ng pinto o bintana. Pinagsama-samang mga istraktura sa sahig ng unang palapag.
Ito ay maginhawa at medyo simple, ang tanging disbentaha ng pamamaraang ito ay na hanggang sa ang bubong ay binuo, at kahit na kasama nito, sa panahon ng pahilig na pag-ulan, ang tubig ay maaaring makuha sa sahig, at sa gayon ay makapinsala sa pagkakabukod.
Ang mga natapos na frame ay itinaas sa pamamagitan ng kamay, na medyo matagal, lalo na sa pakikilahok ng isang maliit na bilang ng mga tao. Kung ikaw ay nagtatayo sa iyong sarili, ipinapayo ko sa iyo na mag-stock up sa isang winch at gamitin ito upang iangat ang mga naka-assemble na anim na metrong pader.
Ang overhead at flooring ay ginawa sa parehong paraan. Ang mga frame ng mga dingding ng ikalawang palapag ay naka-braced din at ligtas na na-install. Ang susunod na hakbang ang gawain ay ang pag-install ng mga rafters mula sa isang 19 cm na lapad na board, na nangangailangan ng isang bahagyang pagsasaayos ng mga guhit ng isang isa at kalahating palapag na 6x9 frame house. Ang proseso ay hindi nangangailangan ng maraming paggawa, ang tanging abala ay ang pangangailangan na magsagawa ng trabaho sa isang sapat na mataas na altitude.
Konstruksyon ng attic ng isang frame house 6x9
Ang highlight ng 6x9 frame house, sa palagay ko, ay ang attic, sa disenyo kung saan ginawa ko ang ilang mga pagbabago. Ayon sa paunang proyekto, dapat itong gamitin ang troso bilang mga rack, na, sa palagay ko, ay hindi lubos na katanggap-tanggap, dahil ang hindi magandang tingnan na malawak na mga bitak ay maaaring lumitaw sa troso sa paglipas ng panahon.
Nagpasya akong mangolekta ng mga rack mula sa mga board. Gayundin, kapag nagtatayo ng tulad ng isang 6x9 frame house na may attic, inirerekumenda kong bigyang pansin ang mga sumusunod:
Una, upang maiwasan ang mga paghihirap kapag pinagsama ang bubong ng bahay at terrace, sulit na tumpak na kalkulahin ang taas ng mga attic rack upang ang mga anggulo ng pagkahilig ng bubong ay eksaktong pareho;
Pangalawa, ang mga attic rafters, tulad ng mga bubong, ay nangangailangan ng espesyal na katumpakan at akma. Upang gawing simple ang trabaho, mas mahusay na isagawa ang mga bubong ng bahay at attic sa iba't ibang antas.
Ang pagpupulong ng mga pediment ay nagdulot ng ilang mga alalahanin, na, gayunpaman, ay naging labis, ang gawain ay tapos na nang mabilis at, na mahalaga, nang may husay.
Dahil napagpasyahan na baguhin ang materyal ng cladding, bahagyang binago ko ang pitch ng mga elemento ng gable.
Ang proseso ng trabaho ay ang mga sumusunod: pagsukat ng distansya sa mga rafters, pagdaragdag ng 10 cm sa taas, paglalagari ng board ng kinakailangang haba, paglakip ng stand sa lugar ng karagdagang lokasyon nito, pagmamarka ng anggulo ng bevel, pag-trim sa kahabaan ng may markang linya, na naka-mount sa stand.
Pag-install ng bubong ng isang one-story frame house 6x9
Para sa bubong ng aking 6x9 suburban frame house, napili ang isang metal na tile, na napagpasyahan na i-install ayon sa lahat ng mga patakaran, ibig sabihin, gamit ang 5x5 cm na mga bar kasama ang mga rafters at isang pahalang na sheathing na gawa sa isang 2.5x10 cm na board. Ang "Scaffolding" para sa trabaho sa taas ay ginawa nang napakasimple - sa pamamagitan ng pag-aayos ng ilang mga board sa mga rack.
Ang susunod isang mahalagang milestone ang konstruksyon ay wall cladding na may ISOPLAAT slab, na, sa proseso ng trabaho, ay napatunayang parehong positibo at negatibong panig... Natutuwa ako na ang pakikipagtulungan sa kanila ay madali - tama sila hugis-parihaba, magaan ang timbang, at madaling i-mount sa dingding.
Ang laki ng isang panel ay 2700x1200 mm, na tumutugma sa distansya sa pagitan ng ibaba at ang overlap ng ikalawang palapag. Kaya, ang lahat ng mga joints ay nag-tutugma sa mga suporta, at ang pagpapakilala ng anumang mga elemento para sa mga joints kasama ang mga gilid ay nawawala, na madalas na sinusunod kapag nagtatrabaho sa isang oriented strand board.
Ang mga disadvantages ng materyal ay kinabibilangan ng hina nito, at hindi angkop para sa paggamit bilang link sa pagkonekta sa pagitan ng mga patayo at kisame, na muling nakumbinsi sa akin sa tamang desisyon na gumamit ng mga braces upang palakasin ang istraktura ng dingding.
Ang pagkakabukod ng mga dingding ng isang frame country house 6x9, presyo ng isyu
6x9 para sa isang paninirahan sa tag-araw, pati na rin para sa mga sahig, nagpasya ako sa basalt wool at pagkatapos ay nahaharap sa tanong ng density ng materyal - 35 o 50 na mga yunit? Dahil binago ang cladding ng bahay, ang hakbang ng mga rack ay naging 55 cm.
Ang pagpili ng isang materyal na may mas mababang density, upang pisilin ito nang kaunti sa mga gilid ng mga rack sa panahon ng pag-install, at bumili ng isang pang-eksperimentong batch, napagpasyahan ko na kung ano man ang density ng mga banig, kailangan nilang putulin. . Sa koneksyon na ito, nanirahan ako sa isang materyal na may density na 35 na mga yunit, ang pinaka-angkop sa mga tuntunin ng ratio ng kalidad ng presyo.
Siyempre, posible na bumili, halimbawa, ang pagkakabukod ng isang dayuhang tagagawa na 56.5 cm ang lapad at mapadali ang pag-install ng trabaho. Ngunit, ang halaga ng naturang cotton wool ay 40 porsiyentong mas mataas kaysa sa domestic product, na, para sa akin personal, ay ganap na hindi kumikita sa pananalapi.
Dito, ang pangunahing gawain sa pagtatayo ng isang 6x9 frame house, ang halaga nito ay minimal sa mga tuntunin ng pagkakaroon ng mga gastos sa paggawa para sa isang pangkat ng mga manggagawa. Maraming tao ang maaaring makayanan ang kanilang sariling mga lakas at kakayahan, na magpapataas lamang ng halaga at kahalagahan ng naturang gusali. Ang trabaho, siyempre, ay hindi pa ganap na nakumpleto, ngunit ang resulta ay nakalulugod na. Sana akin Personal na karanasan at mga balangkas ay makakatulong sa iyo sa pagbuo ng iyong bahay-bakasyunan para sa buong pamilya.