Machine combinée à bois D300, D400. Machine combinée à bois D300, D400 Machine universelle combinée à bois D300
La machine combinée russe pour le travail du bois D-300 est conçue pour le traitement complexe de la menuiserie et des meubles simples dans les entreprises de taille moyenne. Il est possible d'effectuer les opérations suivantes : sciage longitudinal, transversal et angulaire avec une scie circulaire ; rabotage (jointage) le long du plan et du bord ; épaississement avec alimentation automatique de la pièce ; fraisage superficiel diverses configurations (photocopieuse fourni sur demande) et découpe de tenons ; perçage et fraisage de rainures.
Caractéristiques de l'équipement :
- Le lit rigide et les tables en fonte réduisent les vibrations et garantissent une grande précision d'usinage longue durée;
- Entraînement de broche individuel, à partir de 3 moteurs électriques ;
- Haute qualité le fraisage est assuré par une broche verticale à grande vitesse et un système de serrage (en option) ;
- Pour couper les tenons, scier à travers les fibres et en biais, on utilise un chariot à onglets ;
- Les arbres de scie et de fraisage ont la capacité de se déplacer verticalement et lorsque l'un travaille, l'autre se rétracte dans la position la plus basse, le trou est bouché ;
- Épaisseur avec alimentation automatique par deux arbres d'entraînement. Lors du rabotage, les tables de rabotage se replient, ouvrant un accès pratique à la table de rabotage ;
- La table de perçage et de rainurage se déplace horizontalement dans n'importe quelle direction à l'aide d'un système de leviers et verticalement - avec une vis avec volant et poignée ;
- Pour travail sécuritaire la machine est équipée dispositifs de protection et des clôtures. Les boîtiers de protection comportent des connexions pour connecter des éjecteurs de puces ;
- La machine est équipée de pinces et de guides excentriques ;
- De plus, il est recommandé d'installer un chargeur automatique (alimentation automatique) modèle M3 BABY sur la machine.
Ce modèle est le plus pratique et le plus efficace lorsque vous travaillez sur des machines combinées.
Caractéristiques techniques de la machine à bois combinée D-300
Caractéristiques | Signification |
---|---|
Largeur de jointure maximale, mm | 310 |
Longueur totale des tables d'assemblage, mm. | 1520 (1700) |
Largeur d'épaississement maximale, mm | 310 |
Épaisseur maximale de la pièce lors de l'épaississement, mm | 180 |
Profondeur de perçage maximale, mm | 100 |
Longueur maximale de rainure, mm | 100 |
Nombre de tiges de couteaux, pcs. | 1 |
Vitesse de rotation de l'arbre, tr/min | 6000 |
Nombre de couteaux de la tige du couteau, pcs. | 3 |
Vitesse d'avance pendant l'épaississement, m/min | 10 |
Hauteur de coupe, mm. | 85 (maximum) |
Diamètre de la scie (scies), mm. | 315 |
Vitesse de rotation de la lame de scie, tr/min. | 3450 |
Diamètre maximum des fraises utilisées, mm. | 160 |
Diamètre de plantation des couteaux, mm. | 32 |
Vitesse de broche, min -1 | 6000, 8000 |
Puissance totale installée, kW | 8,2 |
Tension d'alimentation nominale, V | 380 |
Dimensions hors tout, mm. | 1950x1520x1450 |
Poids |
La machine combinée russe pour le travail du bois D-300 est conçue pour le traitement complexe de la menuiserie et des meubles simples dans les entreprises de taille moyenne. Il est possible d'effectuer les opérations suivantes : sciage longitudinal, transversal et angulaire avec une scie circulaire ; rabotage (jointage) le long du plan et du bord ; épaississement avec alimentation automatique de la pièce ; surfaces de fraisage de diverses configurations (copieur disponible sur demande) et tenons coupants ; perçage et fraisage de rainures.
Caractéristiques de l'équipement :
- Le lit rigide et les tables en fonte réduisent les vibrations et garantissent une précision de traitement élevée pendant une longue période ;
- Entraînement de broche individuel, à partir de 3 moteurs électriques ;
- Un fraisage de haute qualité est assuré par une broche verticale à grande vitesse et un système de serrage (en option) ;
- Pour couper les tenons, scier à travers les fibres et en biais, on utilise un chariot à onglets ;
- Les arbres de scie et de fraisage ont la capacité de se déplacer verticalement et lorsque l'un travaille, l'autre se rétracte dans la position la plus basse, le trou est bouché ;
- Épaisseur avec alimentation automatique par deux arbres d'entraînement. Lors du rabotage, les tables de rabotage se replient, ouvrant un accès pratique à la table de rabotage ;
- La table de perçage et de rainurage se déplace horizontalement dans n'importe quelle direction à l'aide d'un système de leviers et verticalement - avec une vis avec volant et poignée ;
- Pour un fonctionnement en toute sécurité, la machine est équipée de dispositifs de protection et de protections. Les boîtiers de protection comportent des connexions pour connecter des éjecteurs de puces ;
- La machine est équipée de pinces et de guides excentriques ;
- De plus, il est recommandé d'installer un chargeur automatique (alimentation automatique) modèle M3 BABY sur la machine.
Ce modèle est le plus pratique et le plus efficace lorsque vous travaillez sur des machines combinées.
Caractéristiques techniques de la machine à bois combinée D-300
Caractéristiques | Signification |
---|---|
Largeur de jointure maximale, mm | 310 |
Longueur totale des tables d'assemblage, mm. | 1520 (1700) |
Largeur d'épaississement maximale, mm | 310 |
Épaisseur maximale de la pièce lors de l'épaississement, mm | 180 |
Profondeur de perçage maximale, mm | 100 |
Longueur maximale de rainure, mm | 100 |
Nombre de tiges de couteaux, pcs. | 1 |
Vitesse de rotation de l'arbre, tr/min | 6000 |
Nombre de couteaux de la tige du couteau, pcs. | 3 |
Vitesse d'avance pendant l'épaississement, m/min | 10 |
Hauteur de coupe, mm. | 85 (maximum) |
Diamètre de la scie (scies), mm. | 315 |
Vitesse de rotation de la lame de scie, tr/min. | 3450 |
Diamètre maximum des fraises utilisées, mm. | 160 |
Diamètre de plantation des couteaux, mm. | 32 |
Vitesse de broche, min -1 | 6000, 8000 |
Puissance totale installée, kW | 8,2 |
Tension d'alimentation nominale, V | 380 |
Dimensions hors tout, mm. | 1950x1520x1450 |
Poids |
Fabricant de machine combinée à bois D-400 est une entreprise Tehsnab, OOO, Ivanovo. Adresse du site Web : http://tehsnabstanki.ru
La société Tekhsnab développe et produit des machines à bois depuis 1992.
- D-250
- D300
- D-400
- D300/260
- D300FR
- D300F1300
- D300F2000- la machine est divisée en 2 machines indépendantes. Huit fonctions
- D300F2600- la machine est divisée en 2 machines indépendantes. Huit fonctions
- D-400FR- le matériel ne comprend pas les appareils suivants : - fraisage, sciage circulaire, tenonnage, perçage et rainurage
Machine à bois combinée D-400. Objet, portée
La machine combinée à bois est conçue pour le traitement complexe de la menuiserie et des meubles simples sciage, rabotage (rabotage), fraisage avec fourniture manuelle de pièces dans les entreprises de taille moyenne.
Avec les paramètres appropriés, les types de traitement suivants peuvent être effectués sur la machine :
- rabotage (jointage) sur un plan jusqu'à 410 mm de largeur et jusqu'à 4,3 mm de profondeur en un seul passage ;
- rabotage le long des nervures (bord) selon un angle de 0 à 45° ;
- rabotage unilatéral de planches, poutres avec avance mécanique jusqu'à 320 mm de largeur et jusqu'à 4,3 mm de profondeur ;
- perçage, réalisation de rainures longitudinales et transversales à l'aide de fraises en bout sur un dispositif de perçage et de rainurage.
- scier le long et à travers les fibres de planches jusqu'à 80 mm d'épaisseur à une vitesse d'avance de la pièce allant jusqu'à 1,5 m/min ;
- scier le long des fibres selon un angle de 0 à 45° à l'aide d'une règle ;
- scier des dalles, des planches dans le sens du fil (découpe) droites et en biais à l'aide d'un chariot à onglets ;
- fraisage avec des fraises profilées jusqu'à Ø180 mm ;
- couper des tenons avec des couteaux profilés à l'aide d'un chariot ;
- fraisage courbe avec fraises profilées selon gabarit (copieur sur demande).
Broche de rabotage (arbre de couteau) :
Broche de scie :
Broche verticale de fraisage :
Caractéristiques de conception de la machine multifonctionnelle D-400
- Le banc rigide et les tables en fonte réduisent les vibrations et garantissent une précision d'usinage élevée pendant longtemps
- Entraînement individuel des broches de sciage, de rabotage et de fraisage par 3 moteurs électriques
- Un fraisage de haute qualité est assuré par une broche verticale à grande vitesse et un système de serrage (en option)
- Un chariot à onglets est utilisé pour couper des tenons et scier dans le sens du fil et en biais.
- Les arbres de scie et de fraisage ont la capacité de se déplacer verticalement et lorsque l'un fonctionne, l'autre se rétracte dans la position la plus basse et le trou est bouché.
- Épaisseur avec avance automatique via deux arbres d'entraînement, tandis que les tables de rabotage sont inclinées, offrant un accès pratique à la table de rabotage
- La table de perçage et de rainurage assure le mouvement : dans un plan horizontal dans n'importe quelle direction à l'aide d'un système de leviers et verticalement - avec une vis avec volant et poignée
- Pour un fonctionnement en toute sécurité, la machine est équipée de dispositifs de protection et de protections : les boîtiers de protection sont dotés de tuyaux pour connecter les éjecteurs de copeaux.
- La machine est équipée de pinces et de guides excentriques.
- La machine a la capacité d'affûter les outils de coupe (perceuses, fraises, etc.), ainsi que couteaux plats avec tranchant droit pour dégauchisseuses et fraises cylindriques préfabriquées.
Conditions d'exploitation : en zones ouvertes, sous un auvent, dans à l'intérieur sauf pour les locaux d'habitation.
Les machines doivent être utilisées dans conditions suivantes:
- Altitude au-dessus du niveau de la mer – jusqu'à 1000 m ;
- Valeur de fonctionnement normale de la pression atmosphérique : 865...1065 GPa (650-800 mm Hg)
- Valeurs normales de température de l'air pendant le fonctionnement de la machine : +10°С... +25°С
- Température de l'air recommandée +17°С... +23°С
- Recommandé humidité relative air pas plus de 75% à 20 ºС
- L'humidité de l'air est autorisée jusqu'à 85% à +25 "C et plus basses températures, mais sans condensation d'humidité.
- Version selon le degré de protection contre l'humidité - non protégé
Kit de livraison pour la machine D-400
Machine complète
Boîte D300.052
Complétude :
- Chariot de tenonnage (assemblé)
- Pince de perçage (assemblée)
- Coin
- Couteaux à raboter (installés sur la machine)
- Scie circulaire 315x32 z=48 (fournie en supplément)
- Coffret de scie à secteurs
- Kit de support (fourni moyennant des frais supplémentaires)
- Insert pour scie circulaire
- Arrêt de scie circulaire
- enveloppe dispositif de fraisage
- Collier de serrage pour boîtier de fraiseuse
- Fraiseuse à anneaux et tôles
- Butée du dispositif de fraisage (installée sur la machine)
- Guide de rabot (assemblé)
- Protection de rabot (montée)
- Dispositif de perçage (assemblé)
- Vis de montage du dispositif de perçage
- Manuel d'instructions
Accessoires supplémentaires pour la machine D-400
- D300K1- Attache de copie à dégagement rapide pour le fraisage incurvé ;
- D300FSh- Dispositif de serrage pour fraisage. Utilisé pour augmenter la productivité de l'unité de fraisage ;
- chargeur automatique- Dispositif d'alimentation automatique ;
- DS2200- Système d'aspiration (aspiration de copeaux).
Machines à bois de la société Tekhsnab
- D300-machine de base. Largeur de jointoiement (épaississement) : 310mm. Poids de l'appareil : 650 kg.
- D-400-machine de base. Largeur maximale de jointoiement (épaississement) : 410 mm. Poids de l'appareil : 780 kg.
- D300/260- machine sans verticale broche de fraisage. Largeur de jonction (épaississement) : 300mm
- D250- la machine est divisée en 2 machines indépendantes : dégauchisseuse et raboteuse
- D300FR- le matériel ne comprend pas les appareils suivants : - fraisage, sciage circulaire, tenonnage, perçage et rainurage
- D-400FR- le matériel ne comprend pas les appareils suivants : - fraisage, sciage circulaire, tenonnage, perçage et rainurage
- D300F1300- la machine est divisée en 2 machines indépendantes. Huit fonctions
- D300F2000- la machine est divisée en 2 machines indépendantes. Huit fonctions
- D300F2600- la machine est divisée en 2 machines indépendantes. Huit fonctions
D-400 Vue générale de la machine combinée
- Lit D300.101.051
- Réisme D300.200.001
- Dispositif de scie circulaire D300.401.001
- Dispositif de fraisage D300.402.001
- Dispositif de tenonnage D300.403.001
- Dispositif de perçage D300.405.001
Conception de la machine combinée D-400
Lit (D-400.101.051) fig. 1.1. pos. 1.
Le lit est une structure soudée, qui constitue la base de l'installation de scies circulaires, de raboteuses d'épaisseur, de raboteuses, de dispositifs de fraisage et de perçage. Le cadre est monté sur un plan plat et rigide et ne nécessite pas de fondation particulière. L'alignement du lit s'effectue en fonction du niveau dans les sens longitudinal et transversal en ajustant les supports. La conception du châssis prévoit la possibilité d'installer la machine sur des supports vibrants.
Groupe de montage "Reismus" (D300.200.001) fig. 1.1. pos. 3
Le groupe d'assemblage Reismus comprend :
- raboteuse d'épaisseur (D300.201.001)
- dispositif de rabotage (D300.202.001)
Dispositif d'épaisseur (D300.201.001)
Le dispositif raboteuse se compose d'un arbre de couteau et d'un mécanisme d'alimentation, qui sont montés sur deux mâchoires en fonte montées sur le châssis ; la table élévatrice est montée directement sur le châssis ; Un dispositif est également installé sur les joues pour éviter que la pièce ne soit projetée vers le travailleur.
L'arbre du couteau est l'organe de coupe de l'appareil et est un cylindre en acier avec trois couteaux de rabotage fixés dans ses rainures. Les couteaux sont fixés au moyen de boulons de serrage et de cales qui pressent les couteaux contre les plans de support de l'arbre. Le bord inférieur des couteaux est soutenu par des ressorts, ce qui facilite leur alignement et leur réglage. L'arbre du couteau tourne sur deux roulements à billes. Le couple est transmis à l'arbre du couteau à partir d'un moteur électrique installé dans les rainures de la paroi latérale du cadre via un entraînement par courroie trapézoïdale.
La courroie est tendue par le mouvement vertical du moteur électrique dans les rainures.
La table élévatrice est montée dans le boîtier et installée directement sur le châssis. Le levage s'effectue à l'aide d'un volant.
Le mécanisme d'alimentation des pièces se compose de deux arbres (alimentation ondulée et réception lisse), qui sont entraînés en rotation à l'aide d'un réducteur. transmission par chaîne dentée. La puissance est prélevée pour l'alimentation mécanique de l'arbre du couteau à l'aide d'un embrayage à friction (roue recouverte de caoutchouc à ressort) monté sur l'un des arbres de chaîne d'engrenages. La chaîne est tendue par un pignon à ressort.
Le dispositif anti-éjection (butées) est monté sur l'un des maillons des joues en fonte. Pour installer la table élévatrice à une hauteur de bonne taille le traitement est assuré par une règle avec un pointeur.
Lorsque vous travaillez sur la raboteuse, le mécanisme d'alimentation en pièces doit être désactivé à l'aide d'un levier verrouillable.
Réglage et réglage de la raboteuse
Les couteaux doivent être installés de manière à dépasser de 1,5 mm les dimensions de la tige du couteau. Lors de l'installation, contrôlez l'alignement uniforme des couteaux sur toute la longueur de l'arbre.
Commencez à serrer les boulons retenant les couteaux à partir du milieu de la cale. Avant de commencer le travail, assurez-vous de vérifier que les couteaux sont bien fixés. Après avoir allumé le dispositif d'assemblage, assurez-vous qu'il fonctionne normalement et dans le bon sens de rotation. Il est nécessaire de surveiller le fonctionnement des roulements de l'arbre du couteau. Si la température augmente, il est nécessaire de démonter les roulements, de les laver et de remplacer le lubrifiant.
Surveillez régulièrement la tension de la chaîne du mécanisme d'alimentation de la pièce et l'état de revêtement en caoutchouc roue motrice d'embrayage.
Remarque : lors de travaux sur une raboteuse, les tables de rabotage peuvent pivoter sur les supports s'il y a un capot de protection pour l'arbre du couteau.
Dispositif de rabotage (D300.202.001) fig. 1.1. pos. 7
Le dispositif de rabotage se compose d'un arbre de couteau, de tables de rabotage d'alimentation (avant) et de réception (arrière), d'une règle de guidage et d'une protection de l'arbre de couteau. Les tables sont montées sur les bords supérieurs des joues de la raboteuse. Les tables sont réglables en hauteur, ce qui garantit l'élimination des copeaux de différentes épaisseurs du matériau à traiter. La table arrière est réglée au ras du point haut de la trajectoire des couteaux de l'arbre du couteau à l'aide d'une règle et n'est pas sujette à réglage pendant le fonctionnement.
La table avant peut être ajustée en fonction de l'épaisseur d'enlèvement des copeaux requise. Le levage des tables s'effectue en déplaçant des axes le long du filetage, rigidement reliés aux tables.
La règle de guidage sert à guider le matériau à traiter et à planifier les bords selon un certain angle (angle maximum 45°). La règle est fixée avec une pince. La protection de la tige du couteau est réglable en fonction de la largeur du matériau à traiter. L'entraînement électrique est le même pour les appareils raboteuses et raboteuses.
Réglage et réglage du dispositif de rabotage
Surveiller l'état des surfaces des tables. Les fléaux et les nids-de-poule doivent être éliminés. Assurer la fiabilité des éléments de fixation de la règle de guidage. Les exigences restantes pour le réglage et la mise en place du dispositif de rabotage sont similaires à la clause 6.2.3. «Réglage et réglage de la raboteuse d'épaisseur.»
Dispositif de scie circulaire (D300.401.001) fig. 1.1. pos. 2.
Le dispositif de scie circulaire est utilisé pour la coupe longitudinale, transversale et oblique de matériaux.
L'appareil se compose d'une table de travail, d'une règle de guidage, d'une broche rotative avec une scie circulaire.
Le corps de la broche a la capacité de se déplacer le long des guides du support en fonte, sur lesquels la table est fixée rigidement, et le support lui-même est fixé au lit.
Une scie circulaire est installée sur la broche à une extrémité, qui est fixée entre les brides avec un écrou à l'autre extrémité de la broche, une poulie est installée sur laquelle, à l'aide de Courroie trapézoïdale le couple est transmis par le moteur électrique.
Le moteur électrique est monté sur un support pendulaire monté sur la paroi latérale du châssis. La courroie est tendue en déplaçant le support pendulaire.
La hauteur de coupe est réglée à l'aide d'un levier en déplaçant le corps de la broche le long des guides du support et en le verrouillant dans la position souhaitée.
La règle de guidage installée sur la table a la capacité de se déplacer pour ajuster la largeur de coupe. Pour mesurer la largeur de la coupe, une règle est installée au bout de la table.
Pour sciage en croix et en sciant en biais, on utilise un chariot de tenonnage se déplaçant le long de guides parallèles au plan de la scie. Une cornière de butée pour le positionnement de la pièce est installée sur le chariot. Pour couper en biais, l'angle est tourné et fixé dans la position souhaitée.
Le sens de rotation de la scie est vers l'opérateur.
La scie circulaire est fermée par un joint soudé clôture en acier avec un dispositif qui empêche la pièce d'être projetée vers le travailleur.
Un couteau diviseur est installé à l’arrière de la scie circulaire.
Au fond du boîtier se trouve un tuyau pour connecter un dispositif d'aspiration pour éliminer les copeaux.
Réglage et réglage du dispositif de scie circulaire
Placez la scie circulaire sur l'arbre et serrez fermement l'écrou à travers la bride. Vérifiez le sens de rotation de la scie au ralenti. Sens de rotation vers l'opérateur. Vérifiez que le couteau diviseur est bien fixé et que clôture de protection et sa fixation. L'écart entre le couteau sur toute sa longueur et la scie ne doit pas dépasser 10 mm.
Dispositif de fraisage fig. 1.1. pos. 4 (coupe de tenon Fig. 1.1. rep. 5)
Le dispositif de fraisage (coupe de tenons) se compose d'un boîtier bridé sur la surface inférieure de la table de scie circulaire. Une plume se déplace à l'intérieur du boîtier, dans les roulements duquel est installée une broche de fraisage. A l'extrémité de la broche, des fraises de différentes épaisseurs et profils sont installées. Pour l'installation des fraises, il existe un jeu de bagues d'espacement. L'outil est fixé à la broche à l'aide d'un écrou. La broche est déployée en position de travail et réglée en hauteur entraînement manuel, composé d'une paire d'engrenages et d'une vis. En position de travail, la broche est fixée par une butée.
Le moteur électrique d'entraînement est installé sur la plaque du sous-moteur. La courroie est tendue en déplaçant la plaque sur deux rouleaux à pâtisserie, qui sont fixés après réglage.
Le changement de vitesse de rotation de la broche se fait en lançant la courroie sur des poulies double brin.
La broche avec les fraises installées est recouverte d'un boîtier.
A l'arrière du boîtier se trouve un tuyau pour connecter un dispositif d'aspiration pour éliminer les copeaux. La profondeur de fraisage est ajustée en déplaçant le boîtier dans les rainures de guidage (le dispositif de fraisage illustré sur la Fig. 1.1 n'est pas inclus dans l'ensemble de la machine et est fourni moyennant un coût supplémentaire).
Un chariot avec table est utilisé pour couper les tenons. Un angle de butée avec une pince est installé sur la table, vous permettant de baser et de serrer la pièce.
L'angle a la capacité de se déplier, ce qui permet de couper des tenons sous différents angles.
Lorsque vous travaillez sur une scie circulaire, la broche du dispositif de fraisage (tenonnage) est réglée sur sa position la plus basse et le trou dans la table est fermé avec un bouchon spécial.
Lorsque vous travaillez sur un appareil de fraisage (tenonnage), la scie circulaire de la scie circulaire doit être installée dans la position la plus basse et solidement fixée, et son capot de protection doit être retiré.
Réglage et réglage du dispositif de fraisage (coupe-tenon)
Abaissez la lame de scie circulaire à sa position la plus basse et verrouillez-la solidement.
Retirez le bouchon de la table et étendez la broche en position de travail. Installez la fraise (jeu de fraises) sur la broche à l'aide de bagues et serrez-la solidement avec un écrou.
Installez le guide avec un guide-chaîne (lors du fraisage) ou sans celui-ci (lors de la coupe des tenons) et ajustez-le à taille requise. Fixez solidement la clôture. Réglez le cutter (jeu de couteaux) à la hauteur souhaitée en déplaçant la broche et fixez la plume.
Vérifiez le sens de rotation de la fraise au ralenti.
Sens de rotation vers l'opérateur.
Dispositif de perçage fig. 1.1. pos. 6
Le dispositif de perçage est utilisé pour percer des trous et fraiser des rainures et des évidements.
Le dispositif de perçage est constitué d'une table montée sur un support fixé rigidement à la joue de la raboteuse.
La table a la capacité de se déplacer : verticalement « de haut en bas », horizontalement le long de l'axe et perpendiculairement à l'axe de l'outil de coupe. La table se déplace : en hauteur à l'aide d'une vis avec volant et poignée, dans le plan horizontal à l'aide d'un levier.
La table comporte un support de base pour la pièce et un dispositif de fixation de la pièce.
Réglage et réglage du dispositif de forage
Installez le mandrin de perçage (non inclus dans le kit de livraison) sur l'extrémité conique de la tige du couteau, de la raboteuse et fixez-le avec une vis.
Vérifiez le sens de rotation de la cartouche au ralenti.
Placez l'outil de coupe dans le mandrin et serrez-le.
Vérifiez le faux-rond de l'outil. Si le faux-rond est supérieur à 0,1 mm, remplacez l'outil.
Assurez-vous que la pince à pièce fonctionne de manière fiable.
Une fois le travail terminé, retirez l'outil du mandrin.
Schéma électrique de la machine combinée à bois D-400
Machine à bois D-400. Vidéo
Machine D-400 en fonctionnement
Caractéristiques techniques de la machine combinée D-400
Nom du paramètre | D-250 | D300 | D400 |
---|---|---|---|
Jointage (rabotage) | |||
Largeur maximale de jointage (rabotage), mm | 250 | 320 | 410 |
Profondeur maximale de couche enlevée en un seul passage lors du rabotage, mm | 5 | 4,3 | 4,3 |
Diamètre de la partie coupante de la tige du couteau, mm | 75 | 70 | 70 |
Vitesse de rotation de l'arbre du couteau au ralenti, tr/min | 4000 | 5600 | 5600 |
Dimensions du couteau à raboter, mm | |||
Quantité couteaux à raboter | 3 | 3 | 3 |
Largeur des tables de rabotage, mm | 250 | 320 | 410 |
Longueur totale des tables de rabotage, mm | 1100 | 1420 | 1420 |
Réisme | |||
Maximum et épaisseur minimale flans pendant l'épaississement, mm | 190..5 | 180..5 | 180..5 |
Longueur minimale de la pièce traitée lors de l'épaississement, mm | 300 | 300 | 300 |
Vitesse d'avance de la pièce en mode raboteuse, m/min | 6 | 10 | 10 |
Dimensions plan de travail raboteuse, mm | 252 x 600 | 320 x 550 | 400 x 650 |
Largeur d'épaississement maximale, mm | 248 | ||
Épaisseur maximale de la couche coupée lors de l'épaississement, mm | 2,5 | ||
Hauteur de levage de la table de rabotage ( hauteur maximale pièces à usiner), mm | 195 | 180 | 180 |
Sciage. Dispositif de scie circulaire | |||
Plage de profondeur de coupe, mm | 1..70 | 1..80 | 1..80 |
Le plus grand diamètre de la lame de scie, mm | Ø250x33x3 | Ø250..Ø315 | Ø250..Ø315 |
Diamètre de montage de la scie, mm | 32 | 32, 50 | 32, 50 |
Épaisseur de la scie, mm | 3 | 2 | 2 |
Vitesse de rotation de la scie, tr/min | 4500 | 3500 | 3500 |
Dimensions du plan de travail table de scie, mm | 980 x 470 | 750 x 500 | 750 x 500 |
Dimensions du sommier, mm | 400 x 250 | Course du sommier, mm | 1080 |
Fraisage vertical. Dispositif de fraisage | |||
Mouvement vertical de la broche (épaisseur maximale du matériau à traiter), mm | 80 | 80 | 80 |
Diamètre de montage de la broche de fraisage, mm | 32 | 32 | 32 |
Plus grand diamètre de coupe, mm | 144 | 180 | 180 |
Vitesse de rotation de la broche de fraisage, tr/min | 4500 / 6500 | 6000 / 8000 | 6000 / 8000 |
980 x 470 | 750 x 500 | 750 x 500 | |
Dimensions de la surface de travail du chariot de tenonnage, mm | 250 x 400 | 335 x 450 | 335 x 450 |
Course maximale du chariot, mm | 1080 | 900 | 900 |
Forage. Fraisage en bout | |||
Diamètre maximum du foret, de la fraise, mm | 16 | 16 | 16 |
Vitesse de rotation de la perceuse, de la fraise, min | 4500 | 5600 | 5600 |
Dimensions de la surface de travail de la table, mm | 365x150 | 450 x 250 | 450 x 250 |
Profondeur de perçage, mm | 100 | 150 | 150 |
Course longitudinale de la table, mm | 150 | 150 | 150 |
Équipement électrique de la machine | |||
Type de courant d'alimentation | 220 V/380 V 50 Hz | 380 V 50 Hz | 380 V 50 Hz |
Nombre de moteurs électriques sur la machine, pcs. | 3 | 3 | 3 |
Moteur électrique de rabotage, rabotage, dispositif de perçage, kW | 1,5 | 2,2 | 2,2 |
Moteur électrique de scie circulaire, kW | 1,5 | 3,0 | 3,0 |
Moteur électrique du dispositif de fraisage vertical, kW | 1,4 | 3,0 | 3,0 |
Puissance totale des moteurs électriques, kW | 4,4 | 8,2 | 8,2 |
Dimensions et poids de la machine | |||
Dimensions de la machine (longueur x largeur x hauteur), mm | 1260 x 1140 x 970 | 1660x1500x1100 | 2050x1560x1100 |
Poids de la machine, kg | 304/355 | 650 | 750 |
Les opérations suivantes sont effectuées sur la machine :
- Sciage longitudinal, transversal et angulaire avec une scie circulaire ;
- Rabotage (jointage) le long du plan et du bord ;
- Épaisseur avec avance automatique de la pièce ;
- Fraisage de surfaces de configurations diverses (copieur sur demande) et découpe de tenons;
- Perçage et fraisage de rainures ;
- Le banc rigide et les tables en fonte réduisent les vibrations et garantissent une précision d'usinage élevée pendant longtemps.
- Entraînement de broche individuel par 3 moteurs électriques.
- Un fraisage de haute qualité est assuré par une broche verticale à grande vitesse et un système de serrage (en option).
- Un chariot à onglets est utilisé pour couper des tenons et scier dans le sens du fil et en biais.
- Les arbres de scie et de fraisage ont la capacité de se déplacer verticalement et lorsque l'un fonctionne, l'autre est rétracté jusqu'à la position la plus basse et le trou est bouché.
- Épaisseur avec avance automatique via deux arbres d'entraînement, tandis que les tables de rabotage sont repliées, offrant un accès pratique à la table de rabotage.
- La table de perçage et de rainurage assure le mouvement : dans le plan horizontal dans n'importe quelle direction à l'aide d'un système de leviers et verticalement - avec une vis avec volant et poignée.
- Pour un fonctionnement en toute sécurité, la machine est équipée de dispositifs de protection et de protections : les boîtiers de protection sont dotés de tuyaux pour connecter les éjecteurs de copeaux.
- La machine est équipée d'une pince excentrique et de règles de guidage.
CARACTÉRISTIQUES TECHNIQUES DES MACHINES D300, D400 :
Naïb. largeur de jointoiement et d'épaississement, mm |
||
Naïb. Épaisseur lors de l'épaississement, mm |
||
Longueur des tables d'assemblage, mm |
||
Vitesse d'alimentation pendant l'épaississement, m/min. |
||
Naïb. profondeur (perçage) et longueur (rainure), mm |
||
Vitesse de rotation de l'arbre du couteau (perceuse), tr/min. |
||
Naïb. épaisseur de sciage, mm |
||
Diamètre de la scie circulaire, mm |
||
Vitesse de rotation de l'arbre de scie, tr/min. |
||
Diamètre de la broche de fraisage, mm |
||
Naïb. diamètre du coupeur installé, mm |
||
Vitesse de rotation de la broche de fraisage, tr/min. |
||
Nombre de moteurs électriques, pcs. |
||
Puissance totale, kW |
||
Dimensions, mm |
1950x1520x1450 |
2050x2080x1450 |
Poids, kg |
OPTIONS SUPPLÉMENTAIRES :
Avantages de l'installation d'un alimentateur automatique :
|
|
Conçu pour étendre les capacités technologiques des machines combinées mod. D300, D400, et peut également être utilisé sur n'importe quel fraiseuseà broche verticale, équipée d'un chariot de tenonnage de toute conception. Dimensions de la table pour le gabarit : 250x600 mm. |
|
Utilisé pour augmenter la productivité de l'unité de fraisage. Pour garantir la sécurité et augmenter la productivité, le matériau traité est pressé par des rouleaux à ressort par le haut et par les côtés. |
Les machines combinées D 300 (K) / D 400 sont conçues pour l'usinage complexe de pièces en diverses races bois à moyen et faible puissance. Les principales opérations réalisées par les machines combinées D 400 / D 300 (K) :
Sciage longitudinal, transversal et angulaire avec une scie circulaire ;
Rabotage le long du plan et du bord, ainsi qu'à une taille donnée avec alimentation mécanique de la pièce ;
Surfaces de fraisage de diverses configurations et tenons coupants ;
Tenons percés et fraisés.
Les machines D 300 (K) / D 400 fournissent conditions sécuritaires fonctionne : tout outils de coupe ont des protections et sont situés sous la table de la machine en position de non-travail. Le lit de fonte et les tables de fonte réduisent les vibrations et maintiennent la précision pendant longtemps. L'entraînement de la broche est individuel, à partir de 3 moteurs électriques.
Pour étendre les capacités technologiques, les machines combinées D 300 (K) / D 400 peuvent être équipées sur demande : un accessoire de tournage, un accessoire d'affûtage et d'affûtage avec un dispositif d'affûtage des couteaux de rabotage, dispositif de fraisage, copieur et table d'appoint-table à rouleaux.
Machines combinées D 400 / D 300 (K) (Russie),
spécifications techniques : Largeur de jointage et d'épaississement, mm Épaisseur maximale d'épaississement, mm Dimensions des surfaces de travail des tables de rabotage, mm Vitesse d'avance de l'épaississeur, m/min Vitesse de rotation de l'arbre du couteau, tr/min Hauteur de coupe de la scie circulaire, mm Course du chariot, mm Diamètre de la scie circulaire et siège, mm Hauteur de traitement de la fraiseuse, mm Longueur du tableau, mm Mouvement vertical maximum de la broche, mm Puissance totale, kW Nombre de moteurs électriques, pcs. Dimensions, mm 2000x2360x1485 Poids des machines D 400 / D 300 (K), kg