La table Asti est bancale, comment la renforcer. Comment réparer une table
L’usure fait généralement des ravages. Les articulations situées en haut des pieds sont particulièrement préoccupantes pour les propriétaires de table.
Lorsqu’ils sont soumis à une pression importante, ils peuvent s’affaiblir et même tomber. Les problèmes qui surviennent souvent incluent les planches de chute existantes qui peuvent s'affaisser et les extensions qui se cassent ou se coincent. De nombreux problèmes peuvent être facilement résolus si vous savez réparer une table.
La plupart des tables conçues pour usage domestique, se composent d'un plateau de table fixé à un cadre et d'une base rectangulaire constituée de sangles horizontales étroites, étroitement reliées aux côtés supérieurs des pieds existants. Parfois, le cadre est connecté à partie supérieure, et les pieds sont boulonnés au cadre. Dans les tables de conception simple, les pieds sont fixés directement sous le plateau existant. Des connexions similaires sont maintenues ensemble de différentes manières: colle qui peut perdre de sa résistance ; chevilles et tenons qui peuvent casser ; vis, plaques ou boulons qui pourraient être desserrés. Les liaisons adhésives qui ont perdu leur adhérence peuvent facilement être restaurées en appliquant nouveau calque colle. Mais pour réparer des ruptures graves entre des pièces individuelles, il peut être nécessaire de déconnecter les connexions, puis de remplacer les pièces cassées. Pour compléter la réparation et la rendre la plus qualitative possible, la connexion peut être renforcée à l'aide de cornières métalliques ou de cales en bois.
Réparation d'une table avec un mécanisme coulissant
Comment réparer une table qui a mécanismes coulissants? Pour réparer les tables comportant des pièces mobiles, d’autres mesures sont nécessaires. Mécanismes endommagés tables coulissantes peut être corrigé en nettoyant et en lubrifiant ses parties coulissantes ; S'ils sont cassés, pliés ou perdus, ils doivent être remplacés. La méthode la plus simple pour réparer une planche affaissée est de la caler puis de coller la cale sur sa face inférieure.
C'est bien d'avoir un injecteur de colle. Cela aidera à introduire de la colle dans tous les endroits cachés. L'outil le plus important les pinces dépassent également. Vous aurez besoin de pinces en G pour sceller les fissures existantes et de pinces de ceinture pour garantir qu'une pression égale est maintenue sur tous les joints collés du cadre aux pieds. À l'aide de pinces, vous devez placer les pièces les plus fines sous leurs poignées. bois tendre ou des bouchons pour éviter d'endommager la surface des éléments serrés. Pour fermer les sections collées, vous devez appliquer la force minimale requise, car une pression excessive peut entraîner l'expulsion de toute la colle appliquée, laissant le joint sec et faible.
Si vous devez sécuriser une pièce avec un joint claveté, vous aurez besoin d'un gabarit claveté (pour guider la perceuse) et de centres métalliques clavetés. Ces outils aident à garantir un placement précis ainsi que l'alignement de tous les trous de serrure. Les chevilles dotées de rainures spéciales, renforcées par des liaisons adhésives, sont également utiles.
Comment accéder aux zones endommagées
Pour accéder à la connexion endommagée, vous devez retourner la table et la placer sur un tissu plié en plusieurs couches à la fois ou sur un tapis. Retirez le plateau. S'il est fixé au moyen de plaques métalliques compressives insérées dans une rainure sur les sangles du cadre, vous devez retirer les vis et ces plaques et déconnecter le plateau. S'il est soutenu par des vis ou des boulons sur le cadre ou les blocs d'angle, vous devez retirer ces fixations.
Comment réparer une fissure
Si une fissure apparaît autour de l'emboîture dans la partie supérieure de la jambe, il faut injecter de la colle dans la fissure et dans le trou pour cheveux entre le tenon et l'emboîture. Il est nécessaire de comprimer la connexion à l'aide de deux pinces. Tout d'abord, vous devez installer une pince en forme de G sur la zone supérieure de la jambe afin de fermer la fissure résultante ; placez ensuite une ceinture ou une pince tubulaire, en l'étirant du côté extérieur d'une jambe vers le côté extérieur de l'autre, afin de maintenir le tenon dans son alvéole. Laissez la colle sécher toute la nuit ; alors vous devez retirer les pinces.
Pour mettre à niveau une planche pliante en surplomb, Le point le plus éloigné doit être noté là où le pied de la table ou la glissière de support touche le côté inférieur de la planche ; gratter vieille colle et coupez et fixez une petite cale conique à la planche. Coupez une cale dans un morceau de bois dur, appliquez de la colle sur la face supérieure et poussez-la entre la planche et le traîneau, en l'ajustant jusqu'à ce que la planche soit de niveau. Vous devez placer un poids sur le dessus de cette planche pendant que la colle sèche. Après avoir lu cet article, vous saurez comment réparer une table.
FLAT est une technologie de stabilisation et d'alignement de bureau qui offre des fonctionnalités et des économies de coûts jamais vues auparavant dans l'industrie HoReCa.
En 2006, l'inventeur australien Tony Pike a proposé aux restaurateurs sa solution au problème des tables bancales. Selon Tony lui-même, il a assumé cette tâche après les paroles d'un restaurateur qu'il connaissait - il a d'ailleurs noté que le premier à résoudre ce problème deviendrait certainement un milliardaire. Cependant, ce n'est qu'en 2012, après avoir reçu un soutien financier important, après améliorations et modifications, que le produit est entré sur le marché mondial sous la marque FLAT® et a désormais remporté de nombreux prix et reconnaissances. Des chaînes telles que McDonald's et Burger King commandent des produits FLAT pour leurs restaurants.
Bien que la technologie FLAT® puisse fournir une base solide pour presque tout, des escaliers aux... appareils électroménagers aux hélicoptères, cependant, c'est précisément dans entreprise de restauration le plus grand intérêt a été constaté. Comment la technologie FLAT® profite-t-elle aux travailleurs de l’hôtellerie ?
Grâce au pied de table intégré système hydraulique, la table reste non seulement stable sur n'importe quelle surface et s'adapte instantanément aux sols inégaux, mais il devient également possible de combiner deux ou plusieurs tables sans créer de saillie gênante !
Désormais, il n'est plus nécessaire de s'assurer constamment que la table ne vacille pas en plaçant des serviettes, des sous-verres sous les pieds de la table ou en serrant les pieds à vis. Le déplacement des tables est plus facile et les plateaux s’emboîtent parfaitement. Les tables bancales ne gênent plus les clients et le personnel. Moins de plaintes de clients, moins de vaisselle cassée. Vous gagnez du temps sur le service et les revenus de l’établissement augmentent grâce à la mobilité.
Comment fonctionne FLAT® ?
La technologie FLAT répond aux changements de force de pression de la table sur les supports. Lorsque l’un d’entre eux perd le contact avec la surface en raison d’inégalités du sol, la technologie redistribue immédiatement la charge entre les pieds restants. Et un mécanisme spécial breveté les fixe dans une nouvelle position. Grâce à cela, tous les pieds de table ont toujours un point d'appui en dessous. Et peu importe le nombre de fois que vous déplacez la table, le système fonctionne toujours. Et même nettoyage quotidien les locaux ne poseront plus de problèmes - vous n'aurez plus à vous soucier de remettre chaque table exactement à sa place.
Deuxièmement, rien de moins question importante, qui est résolu par FLAT - combinant des tableaux sans projection. Il arrive rarement que deux tables placées côte à côte dans un café ou un restaurant forment une surface plane. La saillie à l'endroit où ils se connectent a l'air terrible, gêne le service et fait basculer les verres. Les critiques des restaurants sont unanimes sur cette question : les tables doivent être jointes sans saillie.
Désormais, tout ce que vous avez à faire pour joindre parfaitement deux ou plusieurs tables grâce à la technologie FLAT est d'aligner leurs bords littéralement pendant une seconde. Vous obtenez une table deux fois plus grande. Maintenant, cela ne ressemble plus à des tables placées les unes à côté des autres au hasard - maintenant c'est réel grande table pour une grande entreprise.
Vous pouvez consulter la gamme complète de produits sur le site Web de notre société à l’adresse www.best4rest.ru ou sur le site Web du fabricant www.flattech.com. Aujourd'hui, plus de 2 000 bases sont disponibles à la commande dans l'entrepôt du groupe SAAP à Moscou et auprès des représentants régionaux.
Il peut y avoir deux raisons. Soit les pieds reposent inégalement sur le sol, soit la table est décollée. Dans le premier cas, vous devez en rechercher la raison : un sol inégal ou des pieds de différentes longueurs. Ici nous parlons deà propos de la table, mais tout cela s'applique pleinement à la chaise et, en général, à tout meuble « à quatre pieds ».
Si la raison est due à des pieds inégaux, nous renversons la table en plaçant une planche de la même largeur sur chaque paire de pieds, comme indiqué sur la Fig. 1 pour vous assurer lequel des quatre pieds est le plus court ou le plus long.
Si l'une des jambes est plus longue que toutes les autres, vous devez la raccourcir. Combien de temps? Ceci peut être déterminé à l’aide d’une tige cible (Fig. 2). Marquez maintenant avec précision la ligne de coupe. À l'aide d'un crayon bien aiguisé, nous traçons d'abord une ligne sur un côté de la jambe, puis sur le côté opposé et scions exactement le long de la ligne. Nous nettoyons la surface coupée et les bords avec une lime.
Si l'une des jambes est plus courte que les autres. Dans ce cas, vous pouvez allonger un pied (la table conservera alors sa hauteur) ou raccourcir les trois autres (la hauteur de la table sera alors plus petite). Si nous avons opté pour la première option et que nous parlons de seulement 1 à 3 mm, nous collons ou clouons une doublure en cuir ou en caoutchouc par le bas jusqu'à la jambe courte.
Si vous avez besoin de construire davantage, à l'extrémité inférieure du pied, nous fixons une doublure en contreplaqué avec de la colle et des vis, dont la taille est légèrement plus grande que la section transversale du pied. Les têtes de vis doivent être fraisées ! Une fois la colle sèche, nous coupons les parties saillantes de la doublure, les corrigeons avec un ciseau et les nettoyons avec une lime.
Si trois pieds doivent être raccourcis à la longueur du quatrième, nous plaçons la table sur un endroit complètement plat et plaçons une cale sous le pied court afin que la table ne vacille pas (Fig. 3). Directement le long de la ligne de contact entre la cale et le bord de la jambe, tracez une ligne avec un crayon et coupez la cale le long de celle-ci. Nous appliquons la partie sciée du coin avec la surface coupante sur les pattes restantes et traçons une ligne le long de laquelle nous les raccourcissons.
Si une table ou une chaise vacille en raison de joints adhésifs faibles, il est nécessaire de les restaurer. Nous procédons ainsi :
- 1. Nous démontons les connexions faibles et retirons la colle.
- 2. Nous connectons à nouveau les pièces avec de la colle. Si vous n'avez pas de grosses pinces à portée de main, prenez une corde solide, enroulez-la deux fois autour de la table et serrez-la en tordant la corde avec un collier en bois (Fig. 4,5). On place d'abord des patins dans les coins sous la corde pour ne pas rayer les meubles.
- 3. Afin de maintenir la distance requise entre les pieds dans leur partie inférieure lors du serrage, nous plaçons entre eux des barres d'espacement de longueur appropriée.
- 4. Les coins peuvent être renforcés davantage avec des coussinets.
♦ Une ancienne armoire peut être donnée nouveau look, si la surface avant, à l'exception des panneaux, est recouverte de tissu, de papier peint, de film. Matériau de parement La couleur et le motif doivent correspondre au revêtement mural. Une telle armoire sera particulièrement belle dans la chambre.
♦ Pour éviter que les pieds des meubles - chaises, fauteuils, tables - ne rayent le sol, collez dessus des ronds de feutre.
♦ Pour éviter d'endommager les planchers lors du déplacement des meubles, placez des couvercles de boîtes de conserve en plastique sous les pieds – ils réduiront la friction.
♦ Placez un épais tapis de laine sous les pieds de l'objet à déplacer. Avec son aide, il est plus facile de surmonter les rapides. Il faut deux personnes pour travailler : l'une tire le tapis, l'autre pousse le meuble.
♦ Il n'est pas si facile de retirer un bureau, une commode ou une table de nuit lorsque la poignée se brise. Un piston vous aidera à faire face à cette tâche. Il suffit de le plaquer contre le tiroir à proximité de l'endroit où se trouvait la poignée et de le tirer vers vous. Le tiroir glissera facilement s’il n’est pas surchargé et ne « colle » pas.
♦ Les meubles polis, les miroirs, les écrans de télévision, les abat-jour et les vitres s'électrifient facilement et attirent la poussière. Pour vous en débarrasser, essuyez les surfaces avec un mélange de 1 part de shampoing, 1 part d'agent antistatique et 8 parts d'eau.
♦ Si un tiroir de cuisine ou bureau s'ouvre difficilement, essuyez les bords du tiroir et les rainures dans lesquelles il s'insère avec du savon sec ou une bougie.
♦ Après avoir tapissé l'appartement et lavé les sols, les meubles peuvent être remis à leur place, mais vous ne devez pas les pousser fermement contre les murs avant dix jours. Il est également déconseillé d’accrocher des rideaux, tapis, tableaux et autres objets avant cette date.
♦ La propreté et le confort d'un appartement dépendent en grande partie de la disposition des meubles et des tapis.
♦ Les meubles sont sensibles aux changements de température et d'humidité de l'air dans l'appartement, ainsi qu'à l'action soleil. Ceci est particulièrement important pour les meubles recouverts de vernis. Dans les pièces humides, il devient terne et des taches apparaissent dessus. À température élevée En raison du séchage du bois, la couche de vernis se couvre d'un réseau de petites rides.
♦ La lumière directe du soleil (surtout celle qui n'a pas traversé verre à vitre) provoquent des modifications irréversibles de la couche de vernis : elle devient terne, couverte de taches et de fissures. Revêtements de vernis Ils perdent également leur aspect en raison de l’exposition à l’eau, aux solvants ou au contact d’objets chauds.
♦ Souvent, par manque de place, tout un entrepôt est aménagé sur le placard : valises, cartons, colis y sont stockés. Ils ne décorent pas du tout la pièce. La situation peut être améliorée si : fermez le tout avec de beaux rideaux. Des supports sont placés entre le placard et le plafond (contre eux ou fixés au placard), des tubes horizontaux sont insérés entre eux et les rideaux se déplacent le long des tubes.
♦ Les étagères lourdes peuvent être suspendues à l'aide de boulons. Des trous avec une marge sont percés dans le mur et des boulons y sont cimentés de manière à ce que le filetage dépasse à la longueur requise. Les étagères sont fixées avec des écrous.
♦ À lit en bois n'a pas craqué, il faut mettre des patins en feutre dans les joints.
♦ Au fil du temps, les tables avec pieds amovibles deviennent assez lâches. Ni le serrage des écrous à oreilles ni même le recollage n'aident. Pour éliminer cet inconvénient, vous devez enfoncer des clous sans tête à mi-chemin dans les extrémités des planches qui forment le cadre de la table et percer des trous dans les pieds. Désormais, lors de la torsion des « agneaux », les clous prendront la force de coincement et renforceront les pattes de manière fiable.
♦ Bien entendu, le pied inégal d'une table pivotante peut être limé ou, au contraire, on peut placer quelque chose en dessous. Cependant, il est préférable de corriger le défaut une fois pour toutes en collant une sorte de butée épaisseur requise. Et une petite cale vous aidera à la déterminer avec précision : après avoir éliminé le balancement grâce à elle, on marque dessus au crayon l'endroit où s'arrête la jambe - ce sera l'épaisseur souhaitée de la butée.
♦ Pour les meubles fabriqués à partir de panneaux de particules, les portes s'envolent souvent - les vis ne tiennent pas bien dans les murs. Nous vous recommandons de les renforcer de cette façon : percez soigneusement le trou pour la vis jusqu'à un diamètre de 8 mm, enfoncez-y un bouchon en bois avec de la colle et vissez-y la vis.
♦ Peut-être que les loquets à bille ou magnétiques pour portes de table sont bons, mais ils claquent douloureusement lors de la fermeture et de l'ouverture.
Il existe cependant une option simple et « silencieuse » : utiliser des attaches velcro « bardane », largement utilisées dans l'habillement. Pour ce faire, il suffit de fixer des bandes de tels contrôles velcro sur les portes et à l'endroit où elles sont pressées lors de la fermeture.
♦ S'il n'y a pas assez d'espace dans le couloir et que vous avez une famille nombreuse, une chaussure inhabituelle sur la porte d'entrée vous aidera à ranger facilement de nombreuses chaussures.
Il se compose d'une boîte en bois accrochée à la porte avec une paroi en contreplaqué, sur laquelle sont remplies des poches en forme d'anneaux. tissu épais ou similicuir pour chaussures.
♦ Peu importe si les ressorts du canapé s'affaissent. Jetez les ressorts et étirez (pas très serré) les sangles entrelacées sur le cadre. Leur propre largeur et la distance qui les sépare varient de 40 à 60 mm. Fixez-les bien. Placez dessus un simple tissu résistant, une ou deux couches de mousse dessus, puis à nouveau le tissu. Fixez-le au cadre. Enfin, étirez la tapisserie.
♦ La serrure à « loquet magnétique » ne nécessite aucune recommandation. C'est pratique et fonctionne de manière très fiable. Cependant, l'installation du loquet nécessite une précision particulière. Pendant que vous faites ce travail, prenez un morceau de pâte à modeler. Avec la moitié du loquet en place, appliquez couche mince pâte à modeler sur la zone de la porte. Après avoir fermé la porte, obtenez une empreinte exacte de l'emplacement de la seconde moitié du loquet.
♦ Laissez-nous vous rappeler manière fiable réparation de chaises oscillantes. Pour fixation solide tenon dans la douille, la douille doit être élargie de 2 à 3 mm et deux coupes longitudinales doivent être pratiquées dans le tenon sur la moitié de sa longueur. Réalisez ensuite deux cales et insérez leurs extrémités dans les coupes. Lubrifiez la pointe et la douille avec de la colle et insérez fermement le tout à sa place d'origine.
♦ Les pieds des tabourets de cuisine cesseront de se dévisser si des coussinets en caoutchouc sont placés en dessous.
♦ Peu importe si les vis des pieds en bois des tabourets sont desserrées. Vous pouvez les fixer en procédant ainsi : percez la vis avec une perceuse de deux millimètres, percez le pied à moitié, lubrifiez la vis avec de la colle, mettez-la en place et fixez-la avec un clou.
♦ Si le tabouret de la cuisine a cadre en métal dans la douille où est vissé le pied, le filetage est cassé, ne vous inquiétez pas, le problème peut être réglé. Prenez un écrou avec le même filetage et meulez son extrémité. Dans le trou dont le filetage est endommagé, utilisez une lime aiguille pour faire deux coupes pour les saillies de l'écrou et sélectionnez un évidement pour celui-ci dans le siège. Il ne reste plus qu'à insérer l'écrou et à visser le pied.
♦ Les chaises mobiles dotées de supports reliant le cadre peuvent être renforcées. d'une manière simple. Des trous sont percés dans les pieds à une faible profondeur et des trous traversants sont percés dans les entretoises. Après cela, des vis y sont vissées afin que ces dernières serrent les entretoises et les pieds. Les chaises réparées de cette manière serviront encore de nombreuses années.
Si la chaise commence à sécher, seul un démontage complet et un collage ultérieur peuvent la sauver. La seule chose qui peut retarder de plusieurs années une réparation aussi difficile est l'installation d'une paire de coupleurs. Ces attaches sont des tiges filetées en fil d'acier d'un diamètre de 3 ou 4 mm, passées transversalement à travers les pattes et fixées chacune avec une paire d'écrous.
♦ Il arrive que les pieds libres d'une chaise soient encore fermement ancrés dans le cadre du siège et qu'il ne soit pas souhaitable de les défaire. Dans ce cas, il est plus pratique de réparer les pieds en utilisant non pas de la colle, mais coins métalliques: les traces de restauration ne seront pas visibles, et la fiabilité de la fixation est garantie.
♦ Le dossier de la chaise peut être plat, mais un dossier incurvé est beaucoup plus confortable. Comment en fabriquer un ? Cela ne nécessite pas d'équipement spécial et la technologie ici est simple. Assez pour avoir pince à meuble et plusieurs blocs de bois auxiliaires.
Le milieu du dossier en contreplaqué est cuit à la vapeur sur le bec d'une bouilloire bouillante. Ensuite, le dossier est posé sur deux barres, la zone cuite à la vapeur est pressée avec une pince et laissée pendant un jour ou deux dans cette position - la déviation restera même une fois la charge retirée de la pièce.
♦ Pour une raison quelconque, il n'y a toujours pas assez d'espace dans une table de chevet, et une étagère à chaussures dans le couloir n'est pas une panacée. Il est nécessaire de ranger chaussures, bottes et chaussons. Mais mettre le tout en deux couches n’est pas pratique et peu hygiénique.
Nous proposons un moyen simple d'augmenter la capacité de la chaussure. Il est nécessaire, après avoir mesuré la diagonale de l'espace entre les étagères, de découper des inserts en contreplaqué égaux - au lieu d'étagères ordinaires, vous obtiendrez des compartiments triangulaires à deux étages qui pourront accueillir deux fois plus de chaussures, comme s'il y en avait deux tables de nuit en une.
♦ Les étagères d'armoires ne nécessitent pas toujours un poste permanent à un certain niveau. Temporairement, n'importe lequel d'entre eux peut être fixé à la hauteur souhaitée à l'aide de cales en bois insérées entre l'étagère et la paroi du meuble.
♦ Un mouvement imprudent d'un enfant tirant une boîte mur de meubles, — et tout le contenu finit par terre avec fracas. Mais ce n'est pas tant la faute de l'enfant que celle du papa : après tout, il est facile de fabriquer un crochet « frein » dans la boîte à partir d'un petit bloc, en fixant une contre-butée au-dessus de la boîte.
♦ Ce défaut est courant meubles en bois comme le dessèchement. Si des fissures et autres défauts du monolithique bois massif ne violez pas la résistance structurelle du meuble; il se prête parfaitement à la restauration.
Après avoir posé les éléments d'insertion sur la colle et attendu le séchage complet, traiter la surface avec un rabot, puis avec une dégauchisseuse, si nécessaire poncer et poncer papier de verre à grain fin. De ce fait, après une intervention très simple dans apparence armoire ou table, vous ne le reconnaîtrez pas vous-même.
Longeron 15-12-2012 10:02
Plus précisément, ses jambes. La fixation y est délicate, ou plutôt inédite, je prendrai une photo dans une minute. Il n’est donc pas possible de tordre et de tirer. L’ensemble de l’assemblée traîne un peu lentement et c’est tout. C’est juste dommage de jeter la table, elle est comme neuve, même si elle a sept ans.
Est-ce que quelqu'un sait si de tels gadgets sont vendus et est-il possible de les changer ?
Claude 15-12-2012 10:42
Essayez d'abord de le démonter soigneusement. Les fixations sont très probablement des attaches excentriques. Tournez le « canon » avec la flèche et il se démonte. Regardez ce qui ne va pas. Les magasins de quincaillerie de meubles en vendent des similaires (ils ont également des longueurs différentes) - vous pouvez en acheter de nouveaux.
Ou est-ce trivial de s'inquiéter des tenons/vis ?
Ce n’est peut-être pas encore nécessaire.
Sage épouvantail 15-12-2012 10:50
Fabriquez (achetez) des coins en métal, avec des trous - et fixez-les avec des vis, connectez les pieds et les barres. Mais c'est fastidieux - il faut beaucoup de coins (en fait 8) puis tourner pendant longtemps - au moins 4 vis par coin, sinon ça ne se verrouille pas.
Longeron 15-12-2012 11:10
Ce qui devra être démonté est clair. L'essentiel est qu'ils vendent.
Eh bien, d’une certaine manière, il s’agit d’une technologie déjà obsolète, et c’est une corvée, bien sûr.
Je bricolerai si je n'arrive pas à comprendre, ou si je me rends compte qu'il y a beaucoup de bruit - des vis et c'est tout.
Omul 15-12-2012 16:35
Le technologue devrait être lynché. Le tableau est importé. Il s'agit d'une cravate en spirale. J'en ai vu chez les Italiens. Vous ne le trouverez probablement pas en vente. Une très mauvaise solution pour fixer les jambes. Il y aurait une photo de l'unité démontée, il y a une option.
Omul 15-12-2012 17:38
citation : Publié à l'origine par mukdiver :
Convertir pour adapter l'écrou
Oui. Sélectionnez le diamètre et la longueur du goujon ainsi que l'entretoise concave pour l'écrou.
Oui, aucun coin n'est nécessaire. Le vol deviendra lâche. Épaule trop grosse. Et serrez l'écrou.
Kaka 15-12-2012 18:38
diamètre et longueur du goujon
Apparemment, vous avez juste besoin d'une épingle à meuble spécialisée. C'est lorsqu'à une extrémité il y a un filetage métrique (ici vous avez besoin d'un standard de meuble M6) et à l'autre extrémité il y a un filetage à travers lequel cette goupille est vissée à la place de celle d'usine, et ainsi de suite.
citation : Publié à l'origine par Omul :
entretoise concave pour écrou
Seule cette épingle à cheveux doit être sélectionnée en fonction de sa longueur. Je viens de renforcer celle de ma cuisine de cette façon ou presque, la différence est dans les détails.
P.S. Mais ma vie ne sera pas assez forte. Apparemment, il est nécessaire de relier les côtés sous la table avec un cavalier métallique, celui-ci se trouve près des pieds.
Longeron 15-12-2012 18:39
sans nom22 15-12-2012 19:25
Encore un an ou deux suffiront. Ensuite, vous pouvez répéter
Longeron 15-12-2012 20:36
Dois-je retirer la fixation ou l'enduire avec ?
sans nom22 15-12-2012 20:44
1. Retirez la fixation.
2. Étalez généreusement et avec parcimonie le PVA avec de la sciure de bois.
3. Serrez la fixation.
4. Essuyez l'extérieur de la zone avec un chiffon.
plongeur muk 15-12-2012 20:45
citation: démonter, mélanger le PVA-M avec de la sciure de bois et assembler en enduisant généreusement.
Encore un an ou deux suffiront. Ensuite, vous pouvez répéter
Ouais et attache-le avec du fil
Claude 15-12-2012 22:29
citation : Publié à l'origine par Spar :
Je n'ai rien trouvé dans les environs... nous devrons organiser une visite au salon de la construction demain
Regarde où ils vendent garnitures de meubles. Vous pouvez contacter des monteurs de meubles que vous connaissez. Vous pouvez également vous renseigner auprès de Mastercity, dans la rubrique mobilier.
Si vous l'avez démonté (il devait être exposé sur le marché de la fixation) - montrez une photo de la cravate (il s'agit probablement d'une cravate) - elle sera plus facile à trouver.
Peut-être quelque chose comme ça - http://www.mdm-complect.ru/cat...D=1560&ID=65033
Omul 16-12-2012 02:28
Il semble que ce soit le cas. Mais la connexion est initialement erronée. Il va se libérer.
épébiteur 16-12-2012 12:05
citation : Publié à l'origine par Spar :S’il n’a pas été lâche depuis tant d’années, il n’est pas nécessaire de le jeter.
C’est juste dommage de jeter la table, elle est comme neuve, même si elle a sept ans.
citation : Publié à l'origine par Spar :
Il n’est donc pas possible de tordre et de tirer. L’ensemble de l’assemblée traîne un peu lentement et c’est tout.
Le bois a séché avec le temps, ou la tige est sortie de quelques mm, donc l'excentrique n'attire pas.
Placez la tige (là où se trouve le filetage) sur bonne colle et vissez-le en place, laissez-le sécher pendant une journée.
Ancien technologue en meubles.
Longeron 16-12-2012 13:11
Hourra!
Tout est réparé. Lors du démontage de l'unité, il s'est avéré que les tiges qui entrent dans la partie d'accouplement sur le filetage des deux côtés étaient desserrées et que le coupleur excentrique n'était tout simplement pas suffisant.
citation : Publié à l'origine par ehpebitor :
donc l'excentrique n'attire pas.
Au fait, l'arbre est bon. rien n'a séché ni cassé nulle part.
Il suffisait donc de démonter l'ensemble des deux côtés, de visser les tiges - et tout s'est bien passé.
Merci beaucoup à tous pour vos conseils et votre participation animée !
La table est à nouveau debout comme un rocher.