Comment coller un autocollant sur une surface en plâtre. Comment coller un film autocollant: caractéristiques, instructions et recommandations
Film autocollant - universel et matériel bon marché, dont le domaine d'application n'est limité que par l'imagination et consiste principalement en décor différentes sortes surfaces. Extérieurement, c'est un rouleau dense, semblable à papier peint standard, mais diffèrent considérablement en termes de performances. Parlons de ce à quoi le film à base d'adhésif est destiné et comment le coller réellement?
Avantages du film adhésif
Avantages du film autocollant :
- Pendant le processus d'installation, le film n'est pas nécessaire équipement spécial, et lors du collage sur des meubles - nivellement préliminaire de la surface, compétences particulières, de sorte qu'en fait, même un enfant puisse faire le travail.
- Il n'est pas nécessaire d'appliquer de la colle sur la surface, car elle est déjà sur le film.
- Vous pouvez coller le matériau sur absolument n'importe quelle surface (verre, bois, fer, etc.).
- Une variété de textures, de couleurs, de nuances vous permettra de créer un intérieur unique et solutions décoratives. Mats et brillants, transparents et non, à motifs et unis, ils deviendront assistants indispensablesà la fois pendant la rénovation et à la maison.
- De plus, prendre soin de la surface encollée avec un tel matériau est un plaisir ! Pour enlever la saleté, il suffit d'essuyer le film avec un chiffon imbibé d'eau tiède savonneuse.
- Mais l'avantage le plus important d'un film à base d'adhésif est que vous pouvez transformer une pièce au-delà de la reconnaissance pour un prix modique. Cependant, vous ne devriez pas acheter le moins cher du marché. matériaux de construction, ainsi que faire confiance à des entreprises non vérifiées. Par bas prix Ils offrent rarement un produit de très haute qualité.
Pose de film autocollant
Considérez les principaux domaines d'application des films à base d'adhésif:
- La fonction traditionnelle du film est de remettre au goût du jour de vieux meubles qui ont perdu leur beauté d'antan et qu'il est dommage de jeter, qu'il s'agisse d'une armoire rayée, d'un meuble à chaussures minable ou vieux tableau. En le collant avec un film, il aura l'air neuf.
- Imitation auto-adhésive une pierre naturelle ou carreaux de céramique, idéal pour la rénovation zone de travail cuisine - un tablier, un comptoir de bar, des comptoirs, ainsi qu'une rénovation des finitions dans la salle de bain.
- Le film à base adhésive rendra l'ancien brillant non seulement aux meubles, mais également aux appareils électroménagers.
- Le film autocollant vous permet de recréer lors du collage sur une surface en verre, qu'il s'agisse d'une fenêtre ou cloison vitre, effet vitrail, givre, visibilité du verre dépoli ou dépoli. Cela est particulièrement vrai pour les résidents des maisons où tout le contenu de l'appartement est visible à travers les fenêtres, et il devient nécessaire de protéger leur espace des regards des passants.
- Portes minables que vous pouvez transformer en utilisant ce revêtement.
- La tache résultante due aux actions de jeunes artistes sur le mur cachera également avec succès un petit élément du film.
Travail préparatoire
La préparation de l'autocollant du film s'effectue dans l'ordre suivant:
- Pour le travail, vous aurez besoin de ciseaux (couteau), d'un crayon, d'un petit chiffon, d'une règle, d'un sèche-cheveux, de colle à papier peint.
- Vous devez d'abord préparer la surface pour l'autocollant du film, en éliminant la poussière, la saleté et les taches grasses. Ensuite, la base est essuyée avec un chiffon propre.
- Pour dégraisser la base, tout détergent ou une solution alcaline. Ensuite, appliquez de l'alcool ou de l'essence et attendez que la surface sèche.
- Si vous avez affaire à surface en bois en contreplaqué ou en planches, en aggloméré ou en plâtre, il doit être apprêté. Pour cela, un vernis polyester ou un adhésif méthyle pour papier peint est utilisé.
- En présence de fissures et d'irrégularités, l'avion doit être poncé papier de verre et du mastic, recouvrant ensuite apprêt acrylique pour assurer une bonne adhésion du film au support.
- Si vous avez besoin de coller un autocollant sur du plastique, du verre, du métal, il est recommandé d'humidifier un peu la base. Mouiller d'abord la surface avec de l'eau et du détergent.
- Lors de la découpe du film en morceaux, soyez guidé par la grille centimétrique appliquée au dos du matériau. Vous devez y appliquer des marques, en tenant compte des dimensions de la surface de travail et en laissant quelques centimètres en réserve.
- Lors de la découpe du film, il convient de prendre en compte son motif. Par exemple, coupez des carreaux stylisés le long des « coutures ». Si le motif est en rapport, il est nécessaire de couper le revêtement exclusivement le long de la face avant. Si vous souhaitez découper un certain motif dans un autocollant, copiez-le d'abord à l'intérieur et découpez-le soigneusement.
Caractéristiques de l'autocollant de film
Parlons maintenant de la façon de coller film autocollant:
- Prenez des motifs fabriqués à partir de ruban adhésif et retirez-en le film.
- Fixez les morceaux de matériau sur la surface de travail avec le côté collant de manière à ce que les dimensions des surfaces du film et de la base correspondent exactement.
- Étalez délicatement le film sur la surface, lissez-le et lissez-le avec un chiffon doux, comme vous le faites lorsque vous tapissez, afin que des bulles ne se forment pas à l'intérieur.
- Lorsque vous travaillez avec une surface grande surface il doit être couvert colle à papier peint, et le film est collé sur un support humide. Ensuite, il doit être soigneusement essuyé chiffon doux sec.
- Si le film se colle presque instantanément avec la base, vous pouvez utiliser de la poudre ou du talc comme assistant pour ralentir l'adhérence.
- Si des bulles se forment lors du collage du film, elles doivent être soigneusement percées, en les lissant plus tard.
procédure de retrait du film
Film autocollant pour bon fonctionnement servira de longues années. Mais si elle l'a perdue vue originale, alors il faut l'enlever, car lorsque la peinture est prévue, la composition ne reposera pas dessus en une couche uniforme, et il ne fonctionnera pas de coller un nouveau film dessus.
Parlons de la façon de supprimer l'autocollant :
- Bien humidifier eau chaude film, laisser tremper quelques minutes.
- À l'aide d'un objet pointu (couteau, spatule), soulevez délicatement le bord et tirez lentement vers vous. Lorsque le film est fortement collé à la surface, un objet pointu aidera. Soyez extrêmement prudent pendant le fonctionnement afin de ne pas rayer le côté à nettoyer.
- Si l'eau chaude ne vous aide pas, utilisez un sèche-cheveux ordinaire. Bien sûr, s'il y en a un de construction, les travaux seront effectués deux fois plus vite, mais un domestique convient également. Vous pouvez même utiliser un ventilateur avec un flux d'air chaud à cet effet.
- Dirigez l'objet chauffant vers la surface du film. Sous l'influence de la chaleur, la colle commencera à prendre du retard.
- Commencez à arracher un film bien chauffé du bord. De plus, réchauffez les endroits difficiles à enlever.
- Retirez la colle qui reste sur la surface avec des liquides spéciaux (alcool, essence, diluant). Gardez à l'esprit qu'ils peuvent commencer à interagir avec le matériau, alors choisissez-en un qui n'endommagera pas l'article à nettoyer.
Ainsi, l'utilisation de film autocollant - solution parfaite quand on voulait ajouter de la variété à l'intérieur familier de la pièce, donner nouvelle vie objets anciens, faire preuve de créativité dans la création éléments décoratifs ou amusez-vous avec votre enfant.
Le film autocollant est remède universel, avec lequel vous pouvez masquer les rayures et divers autres défauts. Elle a une apparence très attrayante, grande couleurs, excellente durabilité et prix abordable. Cependant, pour que tout se passe comme il se doit, vous devez savoir comment coller correctement le film autocollant sur différents types surfaces.
Informations générales sur le matériel
À l'aide d'un film, vous pouvez non seulement masquer divers défauts sur les meubles apparus pendant le fonctionnement, mais également les rafraîchir. apparence avec un investissement financier minime. En présence de matériel et de ciseaux de bureau ordinaires, le processus de collage ne prendra pas plus d'une heure.
Beaucoup de gens choisissent le cinéma pour les raisons suivantes :
- le film est vendu en rouleaux, il est donc très facile de travailler avec ;
- le matériau est assez résistant, grâce auquel il protège parfaitement le meuble de tout dommage mécanique;
- le matériau a un coût assez faible;
- aucun outil spécial n'est requis pour travailler avec le film;
- le matériau protège parfaitement les meubles de la saleté, de la graisse et de tout type d'autres taches ;
- très facile à nettoyer.
Compte tenu de tous ces avantages, nous pouvons affirmer avec certitude que ce matériau est l'un des plus polyvalents, avec lequel vous pouvez mettre à jour rapidement et à moindre coût les éléments d'intérieur, ainsi que les rendre plus frais et intéressants. Cependant, pour que le résultat final soit à la hauteur de toutes vos attentes, il faut savoir bien coller le film autocollant sur le meuble.
Caractéristiques matérielles
Haute caractéristiques de performance les films sont dus à ses caractéristiques. Il se compose de trois couches, chacune étant conçue pour effectuer une tâche spécifique.
La première couche est le devant. Il peut être fabriqué à partir matériaux polymères, feuille ou papier. Cette couche remplit exclusivement des fonctions de protection et évite d'endommager les meubles lors d'une action mécanique.
Le deuxième est couche décorative. Il donne à l'intérieur un aspect plus esthétique et attrayant. Le film peut imiter différents types de surfaces, afin que chaque personne puisse choisir solution parfaite pour votre intérieur, qui sera en parfaite harmonie avec tous les objets de décoration.
La dernière couche est protectrice. Il est retiré avant que le film ne soit appliqué sur la surface.
Ainsi, nous connaissons déjà les avantages des matières premières et leurs caractéristiques, cependant, avant de répondre à la question de savoir comment coller un film autocollant, il est nécessaire de comprendre les principales variétés de ce matériau.
Variétés de films
Il existe deux principaux types de films auto-adhésifs, qui diffèrent par leur composition et leur technologie de production :
- Monocouche - composé de matériaux polymères et d'additifs spéciaux qui augmentent la résistance et la durabilité du matériau.
- Deux couches - le film se compose de deux couches, dont la première est la principale et la seconde effectue éléments décoratifs. Il est beaucoup moins cher qu'un monocouche, mais ses performances sont moins bonnes.
Alors, comment coller un film autocollant de vos propres mains ? Cela ne nécessite aucun outil ni compétence particulière, donc tout le monde peut tout gérer. Et plus en détail sur le processus de collage sera discuté plus tard.
Pose de film autocollant sur meuble
De nombreuses maisons ont meubles anciens, qui est assez usé et doit être remplacé, mais il n'y a tout simplement pas d'argent pour acheter de nouveaux meubles. Par conséquent, chaque personne s'intéresse à la question de savoir comment coller un film autocollant sur un meuble. La première étape consiste à préparer un ensemble outils nécessaires qui comprend les éléments suivants :
- ciseaux de papeterie;
- un morceau de matière molle;
- rouleau;
- acétone;
- apprêt;
- papier abrasif.
Lorsque l'inventaire est préparé, vous pouvez commencer à préparer la surface pour appliquer le film. Pour ce faire, le meuble doit être apprêté, ce qui augmentera considérablement la qualité d'adhérence du matériau au meuble. Il vaut également la peine de serrer tous les boulons pour que le meuble ne se fissure pas ou ne chancelle pas.
Après séchage complet du mélange d'apprêt, vous pouvez commencer à appliquer le film. C'est là que commence la réponse à la question de savoir comment coller un film autocollant. La première étape consiste à prendre des mesures sur le meuble, sur la base desquelles le film est découpé en morceaux.
Lors de l'application de matériau sur un meuble, une extrémité est retirée couche protectrice environ 10 centimètres, après quoi le film est soigneusement et lentement appliqué sur le meuble. Pour qu'après le collage, il ne reste plus de plis ni de bulles d'air, le matériau est lissé avec un rouleau ou un chiffon doux.
Comment coller un film autocollant plus d'une manière simple? Pour cela, vous aurez besoin solution savonneuse, qui doit être humidifié surface de travail. Ensuite, la couche protectrice est complètement retirée du film et appliquée sur le meuble, après quoi elle est lissée avec un morceau de tissu.
Pose de film sur murs et portes
Une question tout aussi courante qui intéresse de nombreuses personnes est : "Comment coller un film autocollant sur un mur ?" Le processus d'application du matériau sur ces types de surfaces a beaucoup en commun avec celui décrit ci-dessus, mais il existe quelques différences.
Pour commencer, vous devrez préparer les outils suivants :
- règle;
- couteau de papeterie;
- crayon simple;
- spatule avec feutre;
- pistolet à air chaud
Si tout ce dont vous avez besoin est à portée de main, vous pouvez commencer à appliquer le matériau. La première étape consiste à préparer le mur pour le collage. Pour ce faire, l'ancien revêtement et la colle en sont retirés. Ensuite, le mur ou la porte est traité avec de l'essence ou de l'alcool et laissé sécher complètement pendant une journée. Ceci est nécessaire pour dégraisser la surface. Pour obtenir une meilleure adhérence, le mur peut être recouvert d'un apprêt.
Lorsque la surface est entièrement préparée, vous pouvez commencer à coller avec un film. Il est appliqué en parties séparées, de sorte que le matériau est d'abord coupé en certains morceaux. En même temps, une petite marge doit être laissée. Lorsque vous appliquez le matériau sur un mur ou une porte, vous devez être extrêmement prudent afin qu'il repose parfaitement à plat sur la surface. Pour éviter les bulles d'air sous le film, le matériau est bien lissé avec un rouleau.
Film adhésif sur verre
Comment coller un film autocollant sur du verre ? Très simple. Tout d'abord, le verre doit être soigneusement lavé de la saleté et essuyé pour qu'il ne reste plus de traces. Après cela, la surface doit être dégraissée avec de l'alcool isopropylique. Ensuite, les dimensions sont tirées du verre, selon lesquelles la pièce nécessaire est découpée dans le film. Dans ce cas, vous devez prendre une petite marge, nécessaire pour éliminer les éventuelles erreurs.
Avant d'appliquer le matériau sur la surface du verre, ce dernier est préalablement humidifié avec de l'eau savonneuse. La couche protectrice est complètement retirée du film et le matériau est appliqué sur le verre, au cours duquel le film est lissé avec une raclette. Le lissage doit commencer par le centre, en se déplaçant progressivement vers les bords du verre. L'excédent de film est coupé.
Erreurs fréquentes
Alors, vous savez déjà comment coller un film autocollant sur une porte. Cependant, afin de satisfaire pleinement le résultat, les erreurs suivantes doivent être évitées :
- le film doit être appliqué sur une surface parfaitement propre ;
- lors de la découpe du matériau, il faut toujours prendre une petite marge pour que le film soit suffisant pour coller le bouclier;
- pour que le motif corresponde, le film doit être coupé exclusivement au niveau des coutures;
- de sorte qu'après l'application du film sur n'importe quelle surface, aucun défaut ne soit visible, il doit être préalablement préparé avec une haute qualité.
Conclusion
Dans cet article, vous avez appris toutes les nuances de l'application d'un film autocollant sur différents types de surfaces. Cependant, afin de ne pas gâcher le matériau, il convient de respecter strictement la technologie de son application, indiquée par le fabricant sur l'emballage.
L'article décrit où le film auto-adhésif est utilisé, ses variétés, ses avantages et ses inconvénients, les principes de collage parois lisses et les coins.
La technologie de collage des murs avec un film autocollant
Le film auto-adhésif résistant à l'humidité est mince, sa face avant est constituée de chlorure de polyvinyle avec du polyester, et le polyester le rend brillant et durable. DE verso il est imbibé de colle.
Caractéristiques de choix pour la salle de bain
Vous pouvez acheter des rouleaux d'une largeur de 45 cm à 90. La longueur d'un rouleau peut aller de 2 m à 15 m.Le matériau peut avoir une teinte pastel ou être brillant, avec un motif, un ornement. Il se présente sous la forme d'un matériau brillant, et mat, lisse ou rugueux. Il peut imiter :
- tapisserie;
- pierre;
- bois;
- le tissu;
- céramique;
- Toile;
- miroir, surface dorée et argentée.
Un matériau ayant un effet fluorescent peut être vendu.
Lors de l'achat d'un film de bain, vous devez lire attentivement les instructions. Seul un matériau résistant à une humidité élevée convient.
Le marquage se fait sous forme de vagues : vague 1 signifie résistance à l'humidité, vague 2 signifie qu'il peut être lavé, vague 3 signifie qu'il peut être lavé avec n'importe quelle composition. Si une brosse et 1 vague sont dessinées, le matériau peut être essuyé avec une brosse douce et des détergents doux. Si la brosse a 3 vagues, alors il est difficile de l'endommager mécaniquement, il est possible de la nettoyer avec des produits abrasifs fins.
Papier peint autocollant pour cuisine et salle de bain: variétés
- Papier peint en liège. Ils sont faits de matériaux artificiels, ont un revêtement de cire, semblable au liège naturel. Ils dureront très longtemps (jusqu'à 20 ans). Garder au chaud dans la pièce, ne pas coincer sons parasites. Ils ne changent pas d'aspect, ils sont antistatiques.
- Film PVC autocollant. Il s'étire bien et est très résistant. Vendu en un ton ou avec un motif, mat, brillant. Elle colle sur les murs, les meubles, Cadres de porte.
- Papier peint photo à base adhésive.
- Le papier peint autocollant satiné imite le tissu.
- Film avec un revêtement spécial. Vous pouvez dessiner dessus avec de la craie ou un marqueur.
- Papier peint autocollant imitant parquet, brique, marbre, cuir.
Vous devez d'abord choisir une teinte et un motif du matériau afin qu'il soit combiné avec d'autres détails de la salle de bain et de la cuisine.
La salle de bain a l'air bien, collée avec un matériau de la même couleur avec une surface légèrement rugueuse. Vous pouvez choisir des impressions avec un paysage marin.
Le film autocollant peut coller non seulement les murs de la salle de bain, mais aussi les tuyaux
Avantages
Les gens choisissent le film autocollant comme finition, car il présente les avantages suivants :
- Après collage, il protégera les murs des infiltrations d'eau.
- Il remplace discrètement le papier peint vinyle lavable.
- Résiste à des températures élevées (jusqu'à 80°C).
- Tolère calmement les changements brusques de température de l'air.
- Adhère bien à divers murs: du bois, du plâtre, du métal, des cloisons sèches, du verre.
- Ils vendent une variété de matériaux, il peut être mat et brillant, uni et à motifs, pastel et couleurs vives, peut imiter le bois, la brique.
- Il est facile à fixer à la surface, pas besoin d'acheter de la colle.
- Il a de bonnes performances.
- L'entretien est minime.
- C'est pas cher et toujours en stock.
Certes, cela a aussi des inconvénients:
- Il durera dans la salle de bain pendant environ 3 ans.
- Sa surface n'est pas respirante, donc l'air ne pénètre pas dans le mur. Par conséquent, de la condensation et de la moisissure peuvent apparaître sur le mur. Pour cette raison, avant de fixer le matériau, traitez les surfaces avec un apprêt possédant les propriétés nécessaires.
Comment coller un film autocollant de vos propres mains: étapes
Outils:
- couteau de montage;
- les ciseaux;
- stylo-crayon;
- règle;
- mètre à ruban;
- spatule en feutre;
- séchoir de chantier.
Un sèche-cheveux est nécessaire pour réchauffer le film, il collera alors parfaitement au mur. Une spatule en feutre servira à corriger l'application, en lissant les murs pour qu'il n'y ait pas de bulles d'air.
Sur quelle surface peut-on coller ?
Tout d'abord, vous devez préparer les murs:
- Si les murs présentent des irrégularités, ils sont poncés, car le matériau collé est mince et peut afficher toutes les irrégularités.
- Si les murs sont en bois, ils sont poncés et recouverts de vernis.
- Les surfaces métalliques doivent être apprêtées. Appliquer 2 couches d'apprêt à base d'acrylique.
- Les cloisons sèches doivent être mastiquées et nettoyées.
- Les murs doivent être nettoyés de la poussière et de la saleté, dégraissés à l'eau.
- Si les rayons du soleil tombent constamment sur le mur, il y a de brusques changements de température de l'air, alors vous devez acheter un film qui a long terme prestations de service.
Quand ne pas coller
Il est impossible de coller le matériau sur une surface présentant des saillies, des dépressions, car le matériau est très fin et tous les défauts seront visibles. Par conséquent, avant le collage, les murs doivent être traités, apprêtés, enduits.
Vous ne devez pas vous en tenir au vieux papier peint, car le film y adhère bien pire qu'à une surface de mastic, et surtout dans la cuisine, car la graisse se dépose sur le vieux papier peint, qui ne peut pas être nettoyé. Ce sera un peu mieux si vous collez un nouveau film sur l'ancien, mais même alors, il ne collera pas bien. Outre, vieux film peut se desserrer.
Comment coller sur un mur plat
- Marquez le matériel. Pour ce faire, dessinez d'abord des carrés du mauvais côté.
- Vous devez couper le rouleau. Laissez 2 cm supplémentaires en haut et en bas. S'il y a un motif avec un rapport, vous devez couper un morceau sur le devant. Si un motif sous la forme d'un carreau est appliqué sur le matériau, il est alors coupé au niveau des coutures du carreau.
- Il est nécessaire de détacher un morceau de papier de 3 à 3,5 cm du film, de fixer la feuille adhésive au mur et de coller la partie séparée.
- Ensuite, retirez lentement mais uniformément le papier du matériau d'une main et, de l'autre main, lissez la pièce sur le mur avec une spatule en feutre avec des mouvements du centre vers les bords.
- Coupez l'excédent de matériau avec un couteau.
- La bande suivante est collée de manière à chevaucher la précédente de 1 cm.
- Si le film est déjà collé, mais qu'il y a une petite quantité de bulles d'air, il est nécessaire de les percer avec une aiguille épaisse, puis de les lisser soigneusement avec une spatule.
- Si le film adhère à la surface, mais que des rides apparaissent, il est nécessaire de le déchirer d'un mouvement brusque, puis de le recoller.
- Il est impossible que le rouleau se colle, car il est difficile de le séparer.
- La colle ne sèchera qu'après 3-4 heures.
- Si le film est placé sur mur de secours, alors il est conseillé d'utiliser un sèche-cheveux de bâtiment pour le séchage.
- Chauffez le film en tenant le sèche-cheveux à une certaine distance afin qu'il ne surchauffe pas, sinon la surface pourrait noircir, fondre ou se souder au mur. Vous devez constamment déplacer le sèche-cheveux, ne vous attardez pas au même endroit.
- Si le mur est exposé au niveau des joints, il vaut la peine d'augmenter le chevauchement d'une toile à l'autre jusqu'à 3 cm.
- Si vous collez de grandes surfaces, vous pouvez y appliquer de la colle à papier peint. Et jusqu'à ce que la colle sèche, collez le film.
- Si le film colle trop vite, il vaut la peine de saupoudrer les murs de talc. Ensuite le film ne collera pas très vite, il y aura du temps pour son repérage selon les besoins.
Comment coller dans les coins
Vous devez couper un morceau et l'attacher de manière à ce qu'il dépasse de 10 cm d'un autre mur.
Collez le film sur l'autre mur de la même manière. Ensuite, il sera collé avec un chevauchement. Et puis couper l'excédent. Repassez le film avec un sèche-cheveux de bâtiment.
Est-il possible de coller du papier peint adhésif dans d'autres pièces
Le film a un petit inconvénient - il ne laisse pas passer l'air. De ce fait, de la condensation peut apparaître sur le mur. Par conséquent, il est nécessaire de prétraiter les murs avec un apprêt présentant certaines caractéristiques. Et puis vous pouvez coller les murs dans n'importe quelle pièce, même dans la pépinière.
Le film autocollant peut également être collé sur les meubles. Pour ce faire, achetez un film imitant la texture du bois. Elle fera plus long terme fonctionnement de l'ancienne étagère, table, armoire. Vous pouvez coller les cadres de porte ou les appuis de fenêtre avec du matériel.
Comment prendre soin
Vous pouvez laver le film avec une éponge humide. Les petites taches peuvent être enlevées avec des détergents neutres. Si les taches sont grandes, essayez de les enlever avec de l'alcool.
Lors du lavage du film, n'utilisez pas de solvants agressifs ni d'abrasifs avec une grande fraction.
Le film autocollant est facile à coller sur le mur, il est bon marché mais pratique, il est facile de le laver pour enlever la saleté et la poussière.
Vidéo utile
Le mur de l'appartement utilisant un film auto-adhésif est l'un des plus rentables et solutions simples lorsque vous souhaitez économiser de l'argent sur les réparations sans compromettre la qualité. Les papiers peints autocollants sont différents types. Dans cet article, nous essaierons de comprendre toute cette diversité, vous expliquerons comment coller correctement ces papiers peints et ce qui est nécessaire pour en nettoyer les murs à l'avenir.
Préparation au collage
Préparation de la pièce pour la peinture
Avant de passer directement au papier peint, vous devez préparer votre pièce. Retirez toutes les prises et interrupteurs d'éclairage sur les murs. Et avant de commencer à coller, décidez de l'endroit où la première bande de papier peint sera collée. À cet endroit, vous devez tracer verticalement un trait de crayon à peine visible. La colle doit être exactement le long de cette ligne. Choisissez un endroit moins visible à l'œil nu, car lorsque vous collez la dernière bande de papier peint au mur et qu'elle entre en contact avec la première, il y aura de toute façon un décalage de motif entre eux. Par conséquent, il doit être caché aux yeux humains. Par exemple, un tel endroit peut être derrière un placard, etc.
Il est préférable de ne pas coller toute la pièce depuis le coin. Les coins des pièces sont souvent les endroits les plus inégaux, et lorsque la première bande entre en contact avec la seconde, il peut y avoir un espace visible entre le papier peint. Cependant, si le coin de la pièce est caché, vous pouvez coller la première bande de manière à ce qu'elle contourne ce coin - la plus grande partie doit être sur un mur et la plus petite sur l'autre. Après cela, coupez le plus petit côté afin qu'il forme une ligne verticale droite. Ensuite, vous pourrez éviter les lacunes.
Quels sont les outils nécessaires
Étant donné que le film mural autocollant ne nécessite pas de couche de colle sur lui-même ou sur, vous aurez besoin du moins d'outils et d'autres éléments. Alors, décidez dans quelle mesure vous tremperez le papier peint. Le conteneur doit être suffisamment large et en même temps long. Recherchez également une éponge et un rouleau pour lisser le papier peint. Utilisez des chiffons doux pour enlever tout excès d'adhésif qui pourrait dépasser des bords.
Types de films auto-adhésifs
Ces papiers peints présentent un certain nombre d'avantages par rapport aux papiers peints conventionnels, parmi lesquels le plus important est qu'ils ne nécessitent pas l'application d'une couche de colle. Et cela simplifie TRÈS grandement la tâche qui vous est confiée. Les autres avantages incluent :
Nous listons les types de films auto-adhésifs :
- Papier peint en liège.
- PVC autocollant.
- Satin.
- Crétacé.
Examinons de plus près chaque option. Ainsi, le papier peint en liège dans sa structure est assez simple. La face avant est en liège naturel. Le liège est en chêne. Les papiers peints en liège absorbent bien toutes sortes de bruits, ont une isolation thermique élevée et sont sans danger pour la santé humaine car ils sont fabriqués uniquement à partir de matériaux naturels. Afin d'augmenter la durée de vie de tels films, leur face avant est généralement recouverte d'une couche de cire.
Un type assez courant d'auto-adhésif pour les murs est le film PVC, que l'on trouve facilement dans n'importe quel quincaillerie(ou à marché de la construction). Comparé au papier peint en liège, le film PVC est beaucoup moins cher, mais ces papiers peints ne sont pas naturels, mais matériau artificiel. Souvent tels Films PVC ils ne sont pas utilisés pour coller des murs, mais pour revêtir des meubles en production. Par exemple, les armoires ou les murs de la cuisine. Les avantages de ce type d'auto-adhésif, malgré leur composante artificielle, incluent une variété d'options pour la texture, les couleurs et les motifs, ainsi que durées prolongées opération.
Les papiers peints autocollants satinés sont les plus résistants à l'humidité et à l'eau, ils ont un aspect plus attrayant (exceptionnellement Beau design), car un tel film est généralement utilisé pour la fabrication de papiers peints photo. D'une autre manière, ces papiers peints sont également appelés tissus.
Enfin, le papier peint crayeux avec son propre revêtement adhésif peut être distingué comme un article séparé. Les concepteurs recherchent constamment de nouvelles solutions attrayantes dans la conception de l'appartement, et cette option mérite l'attention. La face avant d'un tel film est constituée du même matériau que tableau noirà l'école. Maintenant, vous pouvez facilement laisser un message à votre enfant, mari, femme. Dans le même temps, l'utilisation de tels papiers peints sera la plus option pratique. Votre enfant pourra dessiner sur les murs ce qu'il veut, et vous n'aurez pas à recoller le papier peint à cause des dessins.
colle
Et maintenant, il est temps de commencer à coller du papier peint autocollant. Nous allons maintenant découvrir ensemble comment coller un film autocollant. Prenez des ciseaux ou un couteau utilitaire et coupez la première bande de papier peint de manière à ce qu'elle soit légèrement plus longue que la hauteur de vos murs. Collez la première partie du papier peint le long de la ligne verticale tracée. Cela devrait être fait de manière à ce que le bord du papier peint coïncide exactement avec cette ligne. Ensuite, fixez-le au mur, lissez-le avec un rouleau et retirez l'excédent de colle avec une éponge ou un chiffon doux.
Après cela, prenez la bande de papier peint suivante, faites-la tremper (au fait, le temps de trempage pour un certain autocollant est différent, il est indiqué sur l'emballage du papier peint) et fixez-le à la première bande. En étant plus long que la hauteur du mur, vous pouvez ajuster le motif du papier peint en conséquence. Continuez ainsi et bientôt vous atteindrez la dernière bande.
D'ailleurs, très notes IMPORTANTES: essuyez immédiatement l'excédent de colle avec une éponge ou un chiffon ; coupez l'excédent de papier peint avant qu'il ne sèche.
Il existe des papiers peints qui n'ont pas besoin d'être trempés. Le film en est retiré, le papier peint est superposé avec l'un des bords vers le haut, puis lissé de haut en bas avec un rouleau.
Comment décoller
À un moment donné de votre vie, vous déciderez à nouveau. Vos papiers peints autocollants n'ont plus l'air si frais et beaux, ils « tergiversent » l'œil, il faudra donc les retirer avant d'en coller d'autres. Nous avons compris comment coller du papier peint autocollant, mais nous devons maintenant comprendre comment nous en débarrasser? Bien sûr, il existe des papiers peints qui peuvent facilement se décoller du mur. Mais souvent, dans la plupart des cas, les papiers peints autocollants ont exactement la propriété opposée, ce qui ne permet pas de les retirer facilement du mur.
Pour ce processus, vous devrez utiliser divers substances chimiques. Mais avant d'acheter tel ou tel remède, assurez-vous qu'il est sans danger pour la santé humaine. Pas tout produits chimiques passé le test de la façon dont ils affectent les murs. Donc, si vous avez déjà trouvé les bons produits chimiques, versez-les, par exemple, dans un flacon pulvérisateur ordinaire et humidifiez les murs. Après avoir utilisé air comprimé, vous pouvez souffler tout le papier peint des murs avec une forte pression. Toujours sur les murs peuvent rester revêtement adhésif. Comment s'en débarrasser?
Vous pouvez retirer le film à l'aide d'un sèche-cheveux industriel ou d'une torche. Il suffit de chauffer le papier peint autocollant, puis d'utiliser un grattoir en polycarbonate pour le retirer de la surface. Un tel grattoir laissera le moins de défauts sur vos murs.
Une autre option pour enlever le papier peint consiste simplement à le décoller à la main à un angle de 30 degrés. Ce retrait vous aidera à retirer immédiatement la couche adhésive, et pas seulement le film. Mais vous pouvez endommager la surface sur laquelle le papier peint a été collé. Par exemple, si vous l'aviez, la peinture peut se détacher avec le film et la couche adhésive. Vous pouvez également utiliser le nettoyant sur acide citrique qui est absolument inoffensif pour le corps humain.
Conclusion
En résumé, nous notons que le film autocollant est parfait pour ceux qui veulent gagner du temps sur les réparations, tandis que votre appartement sera tout aussi coloré et attrayant si vous avez utilisé de vrais papier peint ou leurs analogues. Les papiers peints autocollants conviennent non seulement aux murs, mais également aux meubles. Par exemple, si vos meubles dans la cuisine ne sont déjà pas attrayants et qu'il n'y a pas encore d'argent pour un nouveau mur de cuisine, vous pouvez les coller avec du ruban adhésif, ce qui donnera immédiatement regard frais non seulement des meubles, mais toute la cuisine dans son ensemble. Nous espérons que vous savez maintenant comment coller un film autocollant. Si vous avez des questions, posez-les dans les commentaires ci-dessous.
Si vous savez coller un film autocollant, vous pouvez transformer l'intérieur de votre appartement en y dépensant un minimum d'argent.
Le film autocollant est devenu populaire il n'y a pas si longtemps, mais a rapidement été reconnu, car. Vous pouvez littéralement décorer n'importe quelle surface avec : vous pouvez le coller sur des meubles, des portes, du papier peint, des fenêtres, etc.
À partir de l'article, vous découvrirez les caractéristiques du film autocollant, quel film est préférable de choisir pour surfaces différentes et sur les règles de travail avec ce matériau sur différentes surfaces.
Des instructions et des vidéos vous aideront à transformer l'intérieur de votre appartement en utilisant ce matériau.
Comme déjà mentionné, le film auto-adhésif est produit pour une variété de surfaces.
Tous les types de film sont presque identiques et sont fabriqués à l'aide de la technologie du ruban adhésif, ce qui donne à ce matériau l'apparence ruban adhésif et papier peint.
Le film autocollant présente les caractéristiques suivantes : résistance à l'humidité et hautes températures, facilité de travail avec ce revêtement, grand choix couleurs et motifs, entretien facile et faible coût.
Le matériau convient à presque toutes les surfaces : il peut être collé sur la céramique, le bois, le plastique, le papier peint, le contreplaqué, le verre, etc.
Le plus souvent, ce revêtement peut être trouvé comme élément de décor, qui est appliqué sur les meubles, le papier peint et les portes.
Si nous parlons de décollement total ou partiel des murs, cela est vrai pour la salle de bain et la cuisine dans la zone de la zone de travail.
Ce choix s'explique simplement : la saleté ne colle pas au film, il est très facile à nettoyer et assez résistant à l'humidité, ce qui est idéal pour la salle de bain.
Parfois, vous pouvez trouver une couverture dans les chambres d'enfants, parce que. dans ce cas, vous n'avez pas à craindre que l'enfant abîme le revêtement mural.
Bien sûr, il peut être quelque peu inférieur au papier peint en termes de propriétés décoratives, cependant, avec une grande variété de couleurs et de motifs sur le matériau, ce problème peut être évité.
Le film de vitrail sera une excellente décoration pour la porte - d'autant plus qu'il n'est pas du tout difficile de le coller sur du verre.
Son seul inconvénient visible est que le matériau doit être collé au mur ou au meuble de manière complètement uniforme afin qu'il n'y ait pas de bulles et d'irrégularités, car. cela le rendra non seulement peu attrayant, mais aggravera également son adhérence sur la surface, et bientôt il commencera à s'éloigner.
Avant d'acheter et de coller le matériau, vous devez décider de la surface sur laquelle il sera situé. La conception et la couleur du film en dépendent en grande partie.
Par exemple, les meubles sont souvent collés uniquement éléments individuels- par exemple, des images ou des parties multicolores du film qui peuvent "faire revivre" de vieux meubles.
Une autre option consiste à protéger les meubles - un film transparent convient à cela. Si vous allez coller le matériau sur les fenêtres, un vitrail avec un motif en mosaïque vous conviendra.
Pour les salons, les chambres et les crèches, vous pouvez sélectionner des dessins autocollants qui s'insèrent sous le revêtement mural principal et peuvent donner de l'originalité à l'intérieur.
Étant donné que l'un des principaux avantages du matériau est la facilité d'entretien et la résistance à l'humidité, dans la salle de bain et dans la cuisine, vous pouvez le coller complètement sur les murs, ou uniquement sur les zones les plus sensibles à la pollution.
Enlever la saleté du film est très simple : vous pouvez utiliser n'importe quel détergent et eau chaude, et si la pollution est forte, l'alcool éthylique aidera.
Matériel de collage
Pour travailler avec ce revêtement, vous aurez besoin des matériaux suivants:
- règle;
- des crayons;
- les ciseaux;
- spatule en feutre
- séchoir de chantier.
Mais avant de commencer à coller le matériau, vous devez mettre la surface en ordre. Tout d'abord, retirez l'ancien revêtement et la colle qui se trouve en dessous.
Le mur doit être très soigneusement nettoyé, puis dégraissé avec de l'essence ou de l'alcool et bien séché. Mieux encore, le matériau conservera un revêtement de vernis lisse.
Si la surface est mate ou rugueuse, avant de la coller, elle peut d'abord être recouverte d'un apprêt ou d'un vernis polyester ou d'une colle méthylique.
Si vous collez le film sur du contreplaqué, du bois, des panneaux de particules, du tissu ou du plâtre, chacune de ces surfaces doit également être préparée - nettoyée de la poussière et de la saleté.
Vous pouvez également traiter la surface avec un apprêt ou du mastic pour une meilleure adhérence au matériau.
Si le film est collé sur du verre ou du métal, la surface doit être légèrement humidifiée, sinon le revêtement n'y collera pas.
Comme il est souvent collé non pas avec des toiles, mais en petites parties, il y a des marques au dos avec un pas centimétrique.
Presque tous les matériaux sont équipés de tels marquages, cependant, si vous avez acheté un film sans celui-ci, vous devez alors faire les marquages vous-même afin de pouvoir le couper correctement.
mieux couper couteau spécial ou des ciseaux. Lors de la coupe, laissez une marge de 1 à 2 cm.
La façon de couper correctement le matériau dépend de son motif: si l'image est constituée de carreaux, vous devez couper au niveau des coutures, et si le motif est en rapport, vous devez le couper par l'avant.
Coller le matériau dans son ensemble n'est pas difficile, mais vous devez être très prudent et prendre votre temps pour que le revêtement soit à plat et ne se gonfle pas.
Préparez-vous au fait que sceller, par exemple, toute la surface des murs de la salle de bain avec un film sera plus difficile que de l'appliquer sur du verre, des portes ou des meubles en bois.
Après avoir préparé le motif, séparez soigneusement le matériau du substrat et appliquez le côté collant sur la surface.
Vous n'avez pas besoin de le coller tout de suite, appliquez d'abord le film et voyez comment sa taille et sa forme s'adaptent à la surface sélectionnée (au début, vous n'avez qu'à coller les 50 premiers mm).
Si tout est en ordre, étalez doucement le film sur la surface, en le lissant immédiatement avec un chiffon doux et sec.
Il est préférable de regarder tout le processus de collage sur la vidéo si vous ne l'avez jamais fait auparavant.
Pour éviter que le matériau ne bouillonne, vous devez le lisser du centre vers les bords, comme vous le faites lorsque vous collez le papier peint.
Si vous remarquez que le film est gonflé, alignez-le immédiatement avec la surface jusqu'à ce qu'il y soit complètement collé.
Si vous collez le film dans la salle de bain et que la zone de travail est grande, vous devez l'appliquer sur le mur préparé, enduit de colle sous le papier peint. Collez le film jusqu'à ce qu'il soit sec, puis lissez-le également avec un chiffon.
Le film de vitrail, ainsi que les films bouclés appliqués sur le verre, les portes et les meubles, adhèrent très rapidement à la surface, cependant, il est beaucoup plus facile de les coller, l'essentiel est que le matériau soit placé uniformément.
Vidéo:
Pour éviter que le revêtement ne colle trop vite, vous pouvez traiter sa surface avec du talc ou de la poudre.
Le film de vitrail est à coller uniquement sur le verre ou le métal humidifié avec de l'eau. Vous pouvez également ajouter de l'eau savonneuse à l'eau - cela vous permettra d'ajuster plus facilement le film à la surface.
Après cela, le verre ou le métal avec un film collé est essuyé avec un chiffon sec de la même manière.
Le film autocollant est bien fixé sur le papier peint. Très probablement, pour eux, vous ramasserez de petits dessins, et non une toile à part entière. Vous devez coller le matériau sur le papier peint en suivant les instructions standard.